搜索资源列表
Otg
- s3c6400 下的usb otg 实现代码-s3c6400 realization of the code under the usb otg
libusb-1.0.8
- 本源码是USB驱动在Linux环境下USB协议的实现,是USB主控制部分-The source is a USB drive in a Linux environment to achieve the USB protocol is part of the USB host control
Bootloader_V000
- C8051F340的USB HID方式的BOOTLOADER,包含使用说明,固件代码(Keil uv3工程),上位机可执行文件.-C8051F340 USB HID mode BOOTLOADER, contains instructions for use, the firmware code (Keil uv3 engineering), host computer executable file.
Form
- pic18f14k50单片机的USB上位机程序-pic18f14k50 single chip USB host computer program
VBNET
- USB上位机VB.NET的源码,只读的 能看 不能改 -USB host computer VB.NET source code, read-only can see can not be changed
S3C2410_CN_datasheet
- S3C2410A中文数据手册,包含内容1,2,3,5,6,7,8,9,10,11,14,15,16,17,18,19,20,21,22,23章,没有的就是USB主接口和从接口那部分-S3C2410A Chinese data handbook, including the contents of 1,2,3,5,6,7,8,9,10,11,14,15,16,17,18,19,20,21,22,23 chapters, not is the USB host interface and from
42pcb
- 该工程是一个FPGA的开发板 主要包括了FPGA芯片:EP3C25Q240C8 FPGA的配置芯片采用:EPCS16 USB芯片:CY7C68013A USB的FLASH采用:24LC64 AD芯片:AD9238 电源部分:LMS1117-3.3两块分别对USB、模拟部分和FPGA供电;LMS1117-1.2为FPGA核心电压;LMS1117-2.5为 IO口及PLL供电 9盏LED,4个开关 主要完成的一个功能是高速模拟信号的采集,以及上位机传输
AppleUSBOHCI
- 苹果公司的OHCI USB主机协议栈的代码,写得非常棒!值得借鉴!-Apple' s OHCI USB host protocol stack code, written in great! Worth learning!
hzhang
- 基于Proteus的hid usb仿真,用的是pic18f2550芯片,实现A/D数据2路采集,然后通过USB传输到PC中,没有上位机程序-Proteus hid usb-based simulation, using a pic18f2550 chip, to achieve A/D data 2-way acquisition, and then transferred to the PC via USB, there is no host computer program
oscillograph
- 用Teechart5控件实现的虚拟示波器,上位机部分源代码!接口为USB,具有图像采集,取点,显示周期,峰峰值,打印等简单功能。-a virtual oscilloscope achieved with Teechart prov5 and USB interface,source code of Host part! With image acquisition, check-point, display cycles, peak-peak value, print and other sim
CP2101
- 把数据通过USB仿的串口CP2102传输到单片机,再返回上位机-The data via USB serial port CP2102 imitation transmitted to the microcontroller, and then return to host computer
49589075usbhidio_vc2003
- usb与上位机通信的程序源码,通过枚举的方式查找设备-usb communication with the host computer program source code, by enumerating the ways to find devices
LPC1768-Xplorer
- LPC1768-Xplorer is a CORTEX-M3 based stamp board for NGX’s mbed-Xpresso Baseboard. The LPC1768 microcontroller has 512KB of internal flash and 64KB RAM. Ethernet MAC, USB Device/Host/OTG interface, 8-channel general purpose DMA controller, 4 UARTs, 2
USB_camera
- 给出Linux 环境下USB驱动的模块层次结构,包括主控制器驱动、USB 核心驱动和USB设备驱动程序组成,以及USB 接口摄像头驱动模块的层次结构,对底层usbvideo 模块进行分析,对usbvideo 中的函数进行了分类,修正其设计上的一个缺 陷,给出上层微型驱动的实现,最后通过移植USB 摄像头驱动程序到三星公司的SMDK2410 开发板的试验成功,使该驱动成 功应用在基于Linux 的嵌入式系统上。-Given Linux environment USB drive mod
16516514546
- ARMUSBsourceCode 利用ARM 微处理器技术和USB HOST进行读写U盘的开发代码-ARMUSBsourceCode the use of ARM microprocessor technology and USB HOST to read U disc development code
CH375EVT
- CH375 是一个USB总线的通用接口芯片,支持USB-HOST主机方式和USB-DEVICE/SLAVE 设备方式。-CH375 is a common USB bus interface chip to support USB-HOST host of ways and means USB-DEVICE/SLAVE equipment.
usb_vc
- 用于与USB接口设备通讯的上位机程序,可将下位机USB接口设备传输的数据送至PC机并处理。每次数据传送都是上位机主动,上位机先发送命令(借用DEMO程序中的版本号部分),下位机收到READ_VERSION命令就发送64字节数据给上位机,并开始计时,每次发送把发送帧数加1,把时间和帧数发送到上位机显示,方便观察;上位机收到64字节数据就又给下位机发送READ_VERSION命令,重复1000次,测试需时31秒左右。64字节中:第2,3字节是发送帧数,第61字节是通信时间(S)-USB interf
CH375DS1
- USB开发常用的主控芯片CH375中文技术手册,具有详细的说明-The development of commonly used USB host chip CH375 Chinese technical manual with detailed instructions
CH375DS2
- 嵌入式usb开发主控芯片CH375中文手册2-The development of embedded usb host chip CH375 Chinese Manual 2