搜索资源列表
PICADCandDS18B20
- PIC与温度传感器DS18B20汇编编程，开发环境MPLAB7.6，还有PIC的AD采样汇编编程，显示采样电压
Blinky
- 260 ad采样-260 sampling ad
AD转换
- 通过ADC0809进行模数转换，中断方式采样，并将结果在PC机上动态显示出来。-through ADC0809 for analog-digital conversion, interrupt sampling, the results on PC Dynamic displayed.
XC866AD例程
- 英飞凌的XC866，AD采样的程序
c8051f020外围接口电路程序
- c8051f020外围接口包括AD采样，中断，I2C，lcd、数码管显示等程序，适合做最小系统的设计
STM32与ADS1110的通讯
- STM32的模块I2C接口与AD采样芯片ADS1110之间通讯的源程序，已经调通可用。
TLC2543程序资料
- tlc2543 ad采样 数码管显示 测试程序
单片机控制的AD对正弦波信号采样后用12864的液晶显示出来
- 单片机控制的AD对正弦波信号采样后用12864的液晶显示出来,Single-chip microcomputer controlled sine wave signal AD to 12864 after sampling the liquid crystal display out
CodeChargerV0.07STM32 STM32智能充电器的程序
- STM32智能充电器的程序，包括AD采样和控制-STM32 procedures Intelligent Charger
ad_flash.rar
- FLASH存储 AD采样 操作FLASH 读取数据,FLASH memory FLASH read operation AD sampling data
ADS7841.rar
- 实现单片机对AD采样芯片ADS7841转换值的提取,The realization of single-chip sampling of the AD converter ADS7841 chip extraction
c51_ads1255.rar
- AT89C51,ADS1255进行ad采样的开发程序，,AT89C51, ADS1255 to the development of procedures for sample ad
C6713_AD_huibian
- dsp c6713汇编程序。内涵：AD采样，数据处理，乘除，开放运算，fir运算，FIFO输出 对学习6713芯片汇编和了解c6713芯片有帮助-dsp c6713 assembler. Content: AD sampling, data processing, multiplication and division, open computing, fir operations, FIFO output of the learning and understanding c6713 67
robot-controller-design
- 非常全面的自平衡小车制作全套资料，包括硬件PCB，软件源代码，上位机软件代码，器件DATASHEET 等。 建模、控制算法及PD调节的取值参考： http://www.mathworks.com/matlabcentral/fileexchange/19147-nxtway-gs-self-balancing-two-wheeled-robot-controller-design 硬件及软件参考如下网站资料； http://www.circuitcellar.c
zhonglichuanganqi
- 基于c8051f340对加速度传感器模块MMA7361的测试程序，并把xyz方向上得重力加速通过单片机的AD采样结果通过显示屏5110显示 -Based on the acceleration sensor module MMA7361 c8051f340 test procedures, and the xyz direction was accelerated by gravity chip sampling results of AD 5110 through the display sh
STC12C5A60S2
- 基于STC12C5A60S2的AD采样程序，使用AD采集电压显示在LCD，-Use AD acquisition voltage display in LCD
EM78P809N
- 义隆 C语言开发程序，关于AD采样检测电压，控制LED灯闪情况等！-void ADrun() { ADRUN=1 while(ADRUN==1) ad1=ADDH ad1=ad1<<1 ad1=ad1+ADD1 ad1=ad1<<1 ad1=ad1+ADD0 }
My_test_adc_pwm_usart
- 基于stm32的AD采样功能，并且通过串口传输到PC上的实现，使用V3.0的固件库，属于基本stm32外设测试-Stm32 of AD based on sampling functions, and transferred to a PC via the serial port on the implementation, use the V3.0 firmware, peripheral part of the basic test stm32
F2812_AD02
- F2812 AD02 T1周期中断启动ADC，实现ADC模块16路通道的采样.AD采样频率为10K，序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器，采样模式采用并发采样。利用通用定时器T1的周期中断来触发AD转换。-F2812 AD02 .T1 cycle interrupt start ADC, the ADC module 16-channel sampling. AD sampling rate of 10K, the sequence generator SEQ1 and S
AD01
- DSP2812的AD转换程序，序列发生器SEQ1和SEQ2级联成一个16通道的序列发生器，采样模式采用顺序采样。AD采样的触发方式采用软件置位的方式。-DSP2812 AD conversion program, the sequence generator SEQ1 and SEQ2 cascades into a 16 channel sequence generator using sequential sampling, sampling mode. AD sampling trigge