搜索资源列表
FFT_Simulation
- DSP2812 FFT代码,使用TI公司的FFT库,使用了CCS中的仿真,测试可用-DSP2812 FFT code, the use of TI' s FFT libraries, the use of CCS in the simulation, the test can be used ~ ~
MatlabCCS
- Matlab与CCS接口.doc 例1、模型的代码生成 例2、应用举例 -Matlab and CCS interface. Doc Example 1, the model code generation example 2, the application example
6
- 6个网页标准全站代码,个人认为还不错。每个都是以div+ccs的模式开发。-6 page standard site-wide code, personal view is that good. Each are div+ Ccs model development.
sinewave_c
- 在ccs上使用定时器实现一个数字震荡器的代码.产生的是正弦波波形。-Ccs use in the realization of a digital timer oscillator code. Sinusoidal waveform is generated.
mpeg2_encoder
- 基于DM642的mpeg2视频编码系统设计与实现 CCS下编写基于DSPBIOS的代码程序-Based on the DM642 s mpeg2 video encoder system design and implementation of CCS under preparation procedure based on the code DSPBIOS
Hardware_Test_Programs
- ccs下对dm6446的测试程序,能够检测ddr,nandflash,uart,usb等硬件电路的裸板测试代码,包含库文件,板级gel文件,开发环境在TI ccs3.3下。-ccs on DM6446 testing procedures can detect ddr, nandflash, uart, usb hardware such as the bare circuit board to test the code, including library files, board-leve
DSPasp
- DSP中的CCs仿真平台,dsp原理这本书的源代码的全部-Ccs DSP in the simulation platform, dsp principle of this book all the source code
flash2
- 在ccs的环境下通过对flash的写入 擦除操作,实现DSP程序开机自运行。代码是c6713得烧写程序-At ccs environment through write flash erase operation, DSP implementation process is running since boot. Code is a programmer c6713 procedures
DSP_MeanShiftwithKF
- 基于TIc6205DSP上开发的MeanShift结合Kalman滤波的代码,能够很好的进行目标的实时跟踪,可在CCS上编译查看,并最终转换成hex文件下载到dsp上使用。-TIc6205DSP based on the development of MeanShift combination of Kalman filtering code, be able to carry out the objectives of good real-time tracking can be compil
Auto_Measure_system
- 利用ccs环境、MATLAB环境、DSP(TMS320F2812)、被测对象和Agilient网络分析仪E5071B,构建一个自动测量系统。 相信大部分人都知道基于NI公司的GPIB总线,可以实现自动测量,但NI公司的方案实在太昂贵,采用MATLAB能够大大降低成本。matlab与ccs之间基于RTDX协议进行数据交换,同时matlab基于TCP/IP协议与E5071B之间通信,源码说明如下: (1)RTDX_ok目录:matlab7.0代码,包含了一个用GUI实现的界面和相关的具体代码
DA
- TMS5000系列DSP, DA转换程序,是一个完整的工程文件,包含汇编和c源代码,可直接在CCS软件中运行-DA conversion code
Fir
- 一个关于数字信号处理中FIR算法的c语言源程序,可以通过在TI公司的CCS软件中硬件仿真或软件仿真产生波形-On digital signal processing algorithm in the FIR of the c language source code is available through the TI' s CCS software or hardware simulation software simulation waveforms generated
JMCCS2
- 在ccs下运行的代码。通过编译 可以运行-Ccs run in the code. Can run through the compiler
video_loopback
- video loop back source code. in CCS 3.3 davinci-video loop back source code. in CCS 3.3 davinci..
dsp5000
- dsp5000系列ccs编程的汇编模块代码-code example for dsp 5000
EDMA
- A code example in CCS for DSP6146 for configure and work with EDMA.
McBSP
- A code example in CCS for DSP6146 for configure and work with MCBSP.
SerialCommunication
- PIC16F877 Serial Communication CCS C Code
PIC16F77CC
- PIC15F877 CCS C Code
traffic
- 本程序在利用TMS320VC5402定时器0中断的基础上,拓展到模拟交通灯--东西两方 的红、绿、黄灯有次序的交叉点亮.本程序是用C语言代码编写的,在CCS环境下调试通过,并在其实验箱上运行成功.-Procedures in the use of the timer 0 interrupt TMS320VC5402 on the basis of the simulation was extended to traffic lights- something the two sides of t