搜索资源列表
asdfasdfasdfa
- 该程序是基于mini2440的MDK环境开发的。以定时器0延时1s对LED进行闪烁的程序-The program is based mini2440 development of MDK environment. Timer 0 to delay 1s carried on flashing LED program
DS18B20
- DS18B20测温程序，控制DS18B20完成一次温度转换定时器A的计数时钟是1MHz，CPU主频8MHz 所以通过定时器延时能够得到极为精确的 us级延时-DS18B20 measurement procedures, control DS18B20 temperature conversion to complete a timer A count clock is 1MHz, CPU clocked at 8MHz so by timer delay can be extrem
38k.8951
- 使用51累单片机用定时器和延时产生38khz的可调占空比方波信号，源码程序，经过实测 -Use an adjustable duty cycle of 51 tired microcontroller generates a square wave signal 38khz, the source program with a timer and delay, measured through
delay_timer
- 多种时钟下的汇编延时程序，基于定时器的，精准-Compilation of a wide range of clock delay under the process, based on the timer, precision
Microchip-SoftwareTimer
- A feature full Software Timer for the microchip line of compilers. Features : Start delay, interval in mili-seconds, selected number of repeats (1-infinity). also allows setting groups of timers (controls a set of timers by group).
LY_STM32
- 基于STM32，利用芯片自带的定时器Systick实现精确的微秒，毫秒延时-Based on STM32, use the chip comes with microsecond timer Systick precise, millisecond delay
51znxc
- 编者按：以下是网友编写的遥控解码程序！一种用延时等待的解码方法，比较容易理解，但缺点是占用CPU运行时间，第二种方法用定时器和外中断的解码方法，初学不易理解，但优点也很明显，第二种方法如果能解决连发解码就比较完美，更完善的红外遥控解码程序，请参考本站TOPAV-2008，TOP51-2005所配程序。 -Editor' s note: The following is written users remote control decoding procedure! One kind w
lesson3_5
- 数码管每隔500ms循环显示0到F，用到了定时器中断和延时子程序-Digital control every 500ms cycle from 0 to F, use a timer interrupt and delay subroutine
11
- 通过PWM定时器延迟一秒，实现一个LED灯的明灭。实验中观察I/O口的值对LED灯的明灭的控制，学习I/O口的输入输出方式和设置，了解PWM的配置方式-Through the PWM timer to delay a second, the realization of a LED lamp at. I/O values for LED lamp light control experiment, learning I/O port input and output method and set
KEY_MUX
- 多按键独立工作程序，使用定时中断，延时消抖，每按一次按键有且只点亮一个led，而且相互间完全没有干扰。-Multi-key independent procedures, the use of the timer interrupt, delay debounce, each time you press the button has lit one and only led, but did not interfere with each other.
delay_timer
- 多种时钟下的汇编延时程序，基于定时器的，精准-Compilation of a wide range of clock delay under the process, based on the timer, precision
timer1-0.tar
- 网上有很多arm驱动18b20的程序，但是那些调试可以，下载但板子上由于延时函数的不正确而不能正常运行，本程序的延时由Timer实现，经测试完全可用。-arm operating procedures DS18B20，the delay function was achieved by Timer。
huxideng
- 这是基于atmega48的呼吸灯编程，是用延时来控制灯的呼吸的，没有用到定时器-This is based on the programming atmega48 breathing light is used to control the light delay breath, did not use the timer
Mystm32
- stm32:定时器中断,10Khz的计数频率，计数500ms stm32时延任务；创建一个周期任务用于每200毫秒往队列中发送五个数值，发送完成产生一个软件中断。-stm32: timer interrupt, 10Khz frequency counting, counting 500ms stm32 delay task create a periodic task for every 200 milliseconds to send five values
stm32-tim3
- 配置STM32的TIM3定时器中断，实现了延时精度1ms的功能，开发工具为IAR。-Configuring the STM32 TIM3 timer interrupt, to achieve a precision of 1ms delay function, development tools for the IAR.
SPK
- 通过 调节循环中的延时量，改变蜂鸣器的频率，效果是影片里可以听到的定时弹快要爆炸时定时器发出的声音-By adjusting the delay through the cycle of change, the buzzer frequency, the effect is timing bomb in the film is about to explode when the timer can be heard the sound of
KEY
- STM32f103ZET6，通过定时中断实现按键去抖动，是延时方法去抖动的改进。程序中通过定时去抖动，控制LED翻转，是基本模型。在触摸屏按键按键等程序中都可以以此为函数模块。-STM32f103ZET6, realized by the timer interrupt button to jitter, jitter is the delay ways to improve. Program by timing de-jitter, flip control LED, is the basic
saomiao
- 这是一个4*4矩阵键盘扫描函数,用状态机实现,不用延时以消抖,只需在一个定时10~12ms左右的中断函数里调用,从而节省了单片机时间-This is a 4* 4 matrix keyboard scan function, using the state machine implemented without delay in order to eliminate shaking, just a timer interrupt function calls in about 10 ~ 12m
DriverForTiny6410
- 按键驱动程序（混杂设备模型） 软件去抖动的原理就是： 定时器延时时刻到的时刻，按键的状态 要和在 定时器 启动 时刻按键的状态一致。-Key driver (hybrid device model) Jitter is the principle of the software to: State timer delay time to time, the keys To start the timer and the key moments in a consisten
5
- 数码管定时器精确延时数码管依次显示0~5-Digital precision delay digital timer displayed in sequence 0-5