搜索资源列表
SYSTICK_SET
- 基于STM32的1ms定时器设置程序，可以精确延时1MS，且延时时间可以改动（8M）-Program, you can set based on the STM32 1ms timer precision delay 1MS, and the delay time can be changed (8M)
STM32_CONTEX-M3_-SysTick
- 这是STM32的滴答滴答定时器，其是COMTEX M3内核里的一个定时器，一般用作精准延时和给系统提供时钟，如UCOS。欢迎下载研究讨论-This is the STM32 ticking timer, and it is the the COMTEX M3 core of a timer, normally used for accurate delay and the system clock, such as UCOS. Download research and discussion
lesson7_mcu_delay_1s_code
- 本文档是基于５１单片机的用内部定时器延时１秒的C语言程序，单片机教程：http://www.ipbb.cn,谢谢！-This document is based on 51 microcontroller with internal timer delay of 1 second C language programming, microcontroller tutorial: http://www.ipbb.cn, thank you!
mcu
- 单片机控制外部设备，读取外部设备状态，外部中断的应用-Microcontroller to control external devices, read the status of external devices, the application of external interrupts, interrupt-depth understanding, variables, and marked the flexible application of the flexible applica
WDT-500013
- 本应用介绍了如何使用监视定时器。 本应用描述了监视定时器的功能并举例说明。-* THIS SAMPLE CODE IS PROVIDED AS IS AND IS SUBJECT TO ALTERATIONS. FUJITSU*/ /* MICROELECTRONICS ACCEPTS NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR*/ /* ELIGIBILITY FOR ANY PURPOSES.
TimerCap
- LPC1700系列定时器捕获程序，通过查询方式实现定时器的捕获功能，用定时器的捕获值做延时，控制蜂鸣器开关。-The LPC1700 series timer capture program by querying the capture function of the timer, capture timer delay, and control the buzzer switch.
ATMEGA16-left-right
- 基于iccavr开发的ATMEGA16单片机，数码管显示循环次数并且可调时间，定时开关，主要功能是闭合其中一个端口，延时一定时间后必和另外一个端口，在延时一定时间后取反另外一个端口，结束后记一次数，循环完成后判断是否达到设定次数，完成则停止，否则开始第一个循环-ATMEGA16 microcontroller based on iccavr developed digital display the number of cycles and adjustable timer switch, th
TWOTIGER
- 8253用定时器2来产生896Hz的音频信号使喇叭发声，我们可以改变定时器2的计数值来改变声音频率，通过发声的延时程序来获得时间长短不同的声音，于是就可以通过编程；来获得声调（频率）和节奏（延时长短），使计算机演奏出乐曲来。-8253 with a 896Hz timer 2 to generate the audio signal to the speaker sound, we can change the timer 2 count to change the sound frequenc
dingshiqi
- 在Keil软件上使用定时器。相对于其他的延时软件，定时器的延时更为准确。-In Keil software timer. More accurate timer delay relative to the delay software.
Light-Control
- 编写实验程序用实验箱上的发光二极管L0～L7模拟动态广告灯，要求采用单片机内部定时器实现广告灯的流水延时功能（延时1秒），并将广告灯状态循环下去。-Preparation of the experimental procedure using light-emitting diodes on the test box L0 ~ L7 simulate dynamic advertising lights require the use of SCM internal timer the adve
STM32_TIM
- STM32定时器的应用，产生1ms的中断和10us的延迟，希望对大家有用-STM32 timer application, generate 1ms interrupt and 10us delay, and hope to be useful
key
- 独立按键程序，用定时器中断做，键扫描间隔为10ms，最终确认键须延时350ms左右。 本按键程序须定义键扫标志,键处理标志和键值寄存器。 P3.2和P3.3为按键，P1口为键显示。 12M晶体，定时处置为5ms-Independent key program, timer interrupt do key scan interval of 10ms, final confirmation of the keys required to delay about 350ms. The k
test_timer_keyscan
- C8051F005单片机扫描独立键盘，不用定时器不用延时函数，节省资源。驱动12232，显示测试结果-The C8051F005 MCU scanning independent keyboard, do not the timer without delay function, save resources. Drive 12232, display test results
51-c
- 基于51单片机的呼吸灯程序代码，有延时和定时器两种程序-Based the 51 microcontroller breathing lamp code, delay and timer two procedures
key-scan
- 特点： 不采用定时器_不延时； 按键在松手后有效,灵敏度高,消耗资源少,运行效率高 -Features: not using timer delay keys let go, high sensitivity, less consumption of resources, high operating efficiency
watchdog
- 看门狗程序。延时程序 程序设定看门狗计时器为5是，计时时间到芯片复位。-Watchdog program. Delay procedures set watchdog timer for 5, time to time chip reset.
Dynamic-LED
- 利用定时器中断，作为延迟函数，数码管动态显示-Use of the timer interrupt, delay function digital dynamic display
mini2440_buttons
- mini2440 已去抖按键驱动，延时用时钟控制。-mini2440 buttons driver.timer control delay.
C51_UART
- 将实验箱232通信的接收端与发送端短接，P1.0接一个发光二极管，编写串口自发自收（查询方式）通信程序，检查本单片机的串口是否完好，如果发送字符与接收字符一致，则P1.0亮一秒灭一秒闪亮；否则，P1.0熄灭。设fosc=11.0592MHz，波特率为9600。要求用定时器T0实现1S的延时。 -Shorted to the experimental box 232 receiving end of the communication with the sender, P1.0 by a li
F06x_ADC2_ExternalInput
- C8051F060 外设ADC2程序.测量一个外部电压,并通过串口和终端打印功能将测量结果传到计算机windows终端.-This program measures the voltage on an external ADC input and prints the result to a terminal window via the UART. The system is clocked using the internal 24.5MHz oscillator. Res