搜索资源列表
Spi_lookback
- DSP与AD7606的SPI串口通讯程序,包含头文件和主程序。-DSP and the AD7606 SPI serial communication procedures, including header files and the main program.
chuankoutongxin
- 在DSP STM32上 用串口调试接收单片机发出的字符数据 ,并进行通信-DSP STM32 character in the serial data received debugging MCU issued and communicate
CH9121DS1
- CH395 是以太网协议栈管理芯片,用于单片机系统进行以太网通讯。CH395 支持三种通讯接口:8 位并口、SPI 接口或者异步串口,单片机/DSP/MCU/MPU 等控制 器可以通过上述任何一种通讯接口控制CH395 芯片进行以太网通讯。-CH395 chip Ethernet protocol stack management, for single-chip system for Ethernet communications. CH395 supports three communi
Ex10_ZQ28335_SCI_COM1
- dsp Tms320F28335 串口SCIB 查询方式,与Pc机双向通信-dsp Tms320F28335 serial SCIB query, two-way communication with the Pc machine
ecap_apwm
- 基于TI公司DSP 283X的串口通讯程序-TI based on the company s DSP 283X serial communication program
v
- 1.DSP的初始设置 2.DSP中断向量表的建立 3.定时中断的编写 4.查询方式异步串口程序的编写 -1.The initial set of DSP 2.DSP interrupt vector table established 3.The timer interrupt preparation 4.Discover write asynchronous serial program
text
- 16位的CRC运算,程序为某项目中DSP从串口接收数据后进行校验。-16bit crc
EMIFA_FPGA
- DSP和FPGA通过EMIFA接口通信,通过串口打印数据来观察,DSP向FPGA中写入数据,FPGA接收数据后加1,DSP读取处理后的数据并通过串口打印显示-DSP and FPGA interface communication via EMIFA, print data through the serial port to observe, write data to the FPGA, DSP, FPGA after receiving data plus 1, the data read
TEST_COM_INT
- DSP tms320f28335串口控制程序-com controller for DSP tms320f28335
SerialPortQT-master
- 此文件是关于串口通信的内容,能实现DSP、单片机等SCI串口的通信。-This material is related to seria port communication. It can used on DSP or Single chip microcomputer.
RS485
- 这是一个用于DSP的RS485串口调试程序-This is a RS485 for the DSP serial debugger
ex8
- DSP实验测试程序,包括串口、定时器、正弦波发生器、直流电机等。-DSP experimental test procedures, including serial port, timer, sine wave generator, DC motor.
SPI_STM32_FPGA
- STM32F1与FPGA通过SPI进行通信,我上传的是32部分的程序,已经通过串口测试成功。此程序可拓展为和单片机,DSP通过SPI进行通信-STM32F1 and FPGA communication through the SPI, I uploaded the 32 part of the procedure has been successfully tested through the serial port. This program can be extended to and s
flashloader_28x
- 基于labwindowsCVI编写的TMS320F28xx的DSP在线升级上位机程序,通过串口实现,并附带串口协议。上位机软件支持使用CCS编译的.out目标文件并自动进行格式转换。 新建cvi工程。将所有文件添加进工程编译即可。-Upgrade based labwindowsCVI prepared TMS320F28xx of DSP Online PC program, through the serial port, and comes with serial protocol.
TMS320F28x_boot
- TMS320F28xx系列的DSP在线升级boot程序,通过串口实现和上位机软件的通信并实现软件在线升级,boot程序分配在Flash的sectorA区,应用程序分配在其他区。 新建CCS工程并将几个文件夹加入编译即可。-TMS320F28xx Series DSP Online Upgrade boot program, and communication through the serial port of the PC software and implementing softwar
luna_V1.2
- DSP1701 控制,aux, i2s 输入 i2s 输出。 串口命令切换音源 。 -it is to control 1701 DSP 。 input aux and i2s , output , i2s 。
REPORT3
- ADI dsp信号处理仿真实验,片内外设及应用 1. 了解DSP外部存储器SDRAM的初始化方法; 2. 掌握DMA控制器的使用方法; 3. 掌握串口的使用方法; 4. 掌握SPI端口的使用方法; 5. 掌握外部标志位(FLAG4-9)的使用方法; 6. 掌握外部中断(/IRQ0~2)的使用方法。 -ADI dsp experiment 3
uart
- 基于FPGA的RS232串口通信程序。可以和MCU的单片机,还有DSP,以及上位机通信 -FPGA- based RS232 serial communication program.And MCU can be single-chip, as well as DSP, and the host computer communication
DSP280x_Gpio
- DSP实现AD采样与串口通信中GPIO口的分配-DSP Practice AD Adoption Kushiguchi Communication in progress GPIO mouth distribution
SCI_RS232andRS485
- dsp通过scic与计算机串口进行485通信(DSP communicate with through computer serial port through SCIC)