搜索资源列表
dspccs2000
- 这是基于dsp的交流电机调速软件.编程环境是ccs2000,算法用的是spwm方法,用的是c语言和汇编混编,程序里有注释..h和.cmd文件是头文件和内存分配文件-ccs2000
3
- 用DSP产生六路PWM波来控制永磁无刷直流电机的转动和换向-Road, with DSP generate six PWM wave to control the brushless DC motor rotation and change to the
dianjitiaosuziliao
- 电机调速是单片机或DSP硬件平台结合电机运行机制设计相应算法,并以软件实现-Motor speed is a microcontroller or DSP hardware platforms, operating mechanism with electrical design corresponding algorithms, and to software implementation
kaiguan
- 控制设备为喷胶机、电磁阀以及电机拖动的纸带组成。喷胶的目的是控制喷胶的长度,在纸带上形成一段一段的胶体,此胶体的长度与间隔可以人工设定。 将编码器安装机器的滚轮上,由机器的滚轮带动编码器旋转,Dsp通过采集编码器的脉冲知道此时滚轮旋转角度及当前的速度,根据当前的速度计算出补偿量,用Dsp控制八电磁阀动作,目前先做控制一个电磁阀动作。-Control equipment for the glue machine, solenoid valves, and motor drag the ta
sensor-closeloop
- 一个DSP2812做的DSP闭环电机控制程序。-close loop motor control prom,C.
Code
- dsp例子程序,包括滤波器,FFT,电机控制等-dsp examples of procedures, including filters, FFT, motor control, etc.
ucOS
- 介绍将实时嵌入式操作系统μC/ OS - II 移植到TMS320L F2407A 芯片的过程,构建了以DSP 为硬件基 础、以实时操作系统μC/ OS - II 为软件平台的深海机器人推进电机的控制系统。采用嵌入式操作系统的 数控系统,具有优异的实时性和更高的智能化水平,同时也降低了数控系统的开发难度。-Introduction to real-time embedded operating system, μC/OS- II ported to TMS320L F2407A chip
AD
- 电机控制程序DSP,是基于TI的2812进行的电机控制程序-Motor control program DSP, is based on TI' s motor control program conducted in 2812
accelerate
- 用来计算单片机,DSP等控制电机的升降速度表的软件-accelerate table software for MCU or DSP
STEP_MOT
- DSP TMS320LF2407 步进电机控制实验-DSP TMS320LF2407 stepper motor control experiment
DCMOTOR
- 这是一个关于SEED-DTK6713的直流电机运转的例程,可以通过此程序来熟悉DSP开发流程!-This is a SEED-DTK6713 on the operation of DC motor routines, you can through this process to become familiar with DSP development process!
2407with2812
- DSP 2407和2812的功能比较,都是对于电机控制开发使用-compare DSP2407 with 2812
QERcesu
- 基于dsp的三相异步电机的速度检测算法的程序,QEP测速部分。我不会谁能帮帮我附件里面是提示,谁会得,发邮箱377279379@qq.com。我QQ377279379-dsp,about Three-phase asynchronous motor,Speed detection algorithm procedure,Speed part of the QEP.
SPWM
- 基于DSP的感应电机控制系统,编译过,能运行-DSP based induction motor control system, compiled, can run
pwm5_6_GPIOA3_exam
- dsp 发生两路PWM,通过GPIO口逻辑控制电机转动方向
Step
- DSP实验箱EL-DSP-EXP-IV+若干实验程序之步进电机模块控制篇-DSP Experiment Box EL-DSP-EXP-IV+ a number of experimental procedures chapter stepper motor control module
F2812doc
- DSP F2812控制直流电机,可通过按键实现9级调速-DSP F2812 DC motor control can be achieved through the key 9 Speed
BLDCM
- BLDCM: 无刷直流电机的DSP程序(TI源程序)-BLDCM: DSP program brushless DC motor (TI source)
fourteenDSPtestprogram
- 14个DSP实验测试程序,包括存储器,串行口,步进电机,硬件中断,定时器,交通灯,滤波器,语音录放,显示屏等-14 DSP experimental test procedures, including storage, serial, stepper motors, hardware interrupts, timers, traffic lights, filter, voice recorder, screen, etc.
DSPDCMotor
- 无刷直流电机的DSP控制系统研究 其调速等-DSP Brushless DC Motor Control System