搜索资源列表
STM8S-inter-SPI-write-5110LCD
- 使用STM8S单片机，通过操作内部SPI模块来驱动诺基亚5110液晶-USE STM8S MCU ,BY OPERATING INTERMAL SPI MODELE WRITE NOKIA 5110 LCD
single
- STC89C52单片机+诺基亚5110LCD输出三路频率可调的车用方波信号。-STC89C52 MCU+ Nokia 5110LCD output three-way adjustable frequency square wave signal of vehicle.
Adafruit-PCD8544-Nokia-5110-LCD-library-master.zi
- Nokia 5110 lcd arduino
LCD
- 基于stm32的5110液晶显示程序，内含使用说明和详细程序步骤说明-Based on the stm32 5110 LCD procedures, containing instructions and procedures in detail
5110
- 液晶Nokia 5110显示屏，可以显示中文汉字，也可以显示相应的英文，带有例程文字库-LCD Nokia 5110 display, can display Chinese characters, can also according to the corresponding English, ride man word stock with a example
5110-PMPU6050---STM32
- STM32F103ZET6使用IIC实现对六轴传感器的数据读取，并使用5110液晶显示六轴数据。包括角速度和倾角的计算。-IIC STM32F103ZET6 use data for a six-axis sensor reads and uses the 5110 LCD six-axis data. Including the calculation of the angular velocity and inclination.
5110-LCD-Display
- 此程序适用于MSP430，程序功能是基于5110LCD液晶显示-This procedure applies to MSP430, the program features are based 5110LCD LCD
3310_routines_GCC
- lcd 5110 interfacing.
NOKIA5110-LCD-DRIVER
- 诺基亚5110的驱动程序，主要用于单片机的开发，充当显示模块。-Nokia 5110 driver, mainly for single-chip development, act as a display module.
STM8-5110
- STM8单片机驱动NOKIA—5110液晶屏程序。-STM8 MCU LCD driver NOKIA5110 program.
demofor51
- 51单片机采集温湿度，光照强度等环境参数并在5110液晶屏上显示-51 single collection of temperature and humidity, light intensity and other environmental parameters and displayed on the LCD 5110
5110
- 主要为了NIKIA5110液晶屏显示的程序-Mainly for the Nokia5110 LCD screen display program
NOKIA-5110
- 适用于51单片机（5V或3.3V）,液晶的VCC接5V或3.3V，修改偏置电压可改变5110点阵显示的亮度-Applicable to 51 single-chip (5V or 3.3V), LCD VCC 5V or 3.3V, modify the bias voltage can be changed 5110 dot matrix display brightnes
5110
- 5110驱动文件，配合头文件显示5110液晶数据(5110 drive files, with the header file to display 5110 LCD data)
STM32_LCD5110
- 主控为STM32F103，使LCD 5110 模块显示时钟(The main control is STM32F103, so that the LCD 5110 module displays the clock)
微型气象站
- 平台为arduino uno r3，采集温湿度，气压、海拔、土壤湿度信息在5110屏幕上显示，并通过nrf24l01传到另外一个arduino采集板上，然后通过串口传给pc机。传感器有ds18b20，dht11，土壤湿度传感器，bmp085，显示屏为5110，一对nrf24l01。library文件夹下为所需的各种库。(The platform for Arduino uno R3, collecting temperature and humidity, air pressure, altit
Speed
- 基于STC15W4K32S4的智能小车测速程序，测速使用光电码盘，显示采用诺基亚5110液晶屏(STC15W4K32S4 based smart car speed measurement program, speed measurement using photoelectric code disk, display the use of NOKIA 5110 LCD screen)
5110液晶显示
- 基于STM32的LCD5110液晶显示代码(LCD5110 LCD display code based on STM32)
UART2LCD
- MSP430G2553开发板驱动串口和5110液晶屏显示的代码。使用IAR打开。(The MSP430G2553 development board drives the serial port and the 5110 LCD screen to display the code. Open with IAR.)
5110-With-CodeVision-www.dmf313.ir-
- for led and lcd 5510 nokia programing