搜索资源列表
TMR
- PIC单片机的定时器C程序,可用于单片的定时器使用参考-PIC microcontroller C program, the timer can be used for single chip timer using reference
源代码
- 这是内部有10位ADC的一个简单应用,这个电路最多测量30 V DC,可以应用在台式电源或各种系统中的面板仪表。 PIC16F676的内部adc与一个电阻网络分压器用于测量输入电压,用数码管来显示电压值,频率在50HZ左右 在原理图中的47K看到和10K电位连接分压器配置。在默认情况PIC微控制器ADC参考电压设置到VCC(+ 5V在这种情况下),分出最大射程30伏到5伏这样的分压器。(This is a simple application with 10 bit ADC insi
ff4b
- fat32的文件管理系统,用于嵌入式sd/mmc卡的简单文件管理系统(FatFs is a generic FAT file system module for small embedded systems. The FatFs is written in compliance with ANSI C and completely separated from the disk I/O layer. Therefore it is independent of hardware architec
FATFS sample code
- Petit FatFs Module Sample Projects DIRECTORIES <generic> Generic microcontrollers with MMC <avr> ATMEL AVR (ATtiny85) with MMC <avr_boot> ATMEL AVR generic MMC boot loader <pic> Microchip PIC
位置式PID
- 位置式PID控制,可用于温度PIC控制,流量PID控制,本案例已经成功应用(Position PID control, can be used for temperature PIC control, flow control PID, this case has been successfully applied)
带位置感应器的直流无刷电机PMW控制仿真
- 本例用PIC单片机控制带感应器的直流无刷电机,通过调节RA0端口的可变电阻器可实现电机调速控制.由于当前版本PROTEUS不支持换向功能,连接RA1端口的SW1尚不能控制无刷电机的运行方向.(This example uses PIC MCU control with inductor DC brushless motor, the variable resistor adjusting RA0 port can realize the motor speed control. The curr
key-pic16f639
- PIC16F639单片机C语言代码,带3D天线可低频唤醒,高频端数据已加密,数据加密用的滚码方式,PIC内部硬件加密没用,软件已测并用于实际项目,MPLAB IDE可直接打开(PIC16F639 microcontroller C language code, with 3D antenna can be low frequency wake-up, high frequency data has been encrypted, data encryption with the roller c
I2CTest_UseSoftI2CModule(PB0,PB1)
- 本程序实现了用TI LM3S系列单片机的IO端口接入I2C总线,可以实时监控总线上的变化与传输,并将I2C传输的内容,实时通过串口打印出来,可用于破解各种I2C通信协议,曾经用于解析PIC单片机之间的I2C通信,解决了串口实时打印的问题,采用FIFO,UART接受与发送均采用中断,并解决了FIFO中断深度等等问题。仅供参考。(This program is used to achieve the IO port access I2C bus by using TI LM3S Series MCU
hosts
- 你可以去p站等图片网站了,可以搜到很多的图哦(you can go to pixv,and look for more pic.)
按键处理办法
- 新型的按键扫描程序,这种按键处理办法的便捷和高效,你可以移植到任何一种嵌入式处理器上面,因为C语言强大的可移植性,你可以在MCS-51,AVR,PIC,甚至是ARM平台上面测试这个程序性能。(The new button scanning program, which is convenient and efficient, can be ported to any of the embedded processors. Because of the portability of the C l