搜索资源列表
RX850_RTOS
- 日本nec公司的实时操作系统 rx-850的介绍, 符合itron规范.-real-time operating systems rx-850 introduction, with Itron norms.
Demos(rx)
- RxRich很有用的文字图像显示控件,这是它的Demo-RxRich very useful text image display controller, which is its Demo
CC2500-DONGLE-RX-V40
- 这个是CC2500在em78p447的程序-the CC2500 is in the process em78p447
9E5-Rx
- 无线单片机nFR9E5的收发程序例子,供参考 -wireless transceiver examples of procedures for reference
UWB_BPSK_transreceiver
- MATLAB仿真uwb使用bpsk调制解调的发送(TX)和接收(RX)-MATLAB uwb bpsk use of modulation and demodulation of this (TX) and receive (RX)
regexplib
- 一套小巧的正则表达式分析库,与gnu rx, regexp 的regcomp(®, regstr, REG_EXTENDED)兼容-a compact is the regular expression analysis, and gnu rx, regexp regcomp (
2262TX
- rf tx coding for TX and RX
rfid_model
- A system simulation environment in Matlab/Simulink of RFID is constructed in this paper. Special attention is emphasized on the analog/RF circuit.Negative effects are concerned in the system model,such as phase noise of the local oscillator,TX-RX
ReceiverKX8AssemblyCode
- 胎压检测接收端汇编源码--tpms-rx
smsc911x_xscale_v1.12
- smsc911x 网卡驱动 This the users/programmers guide for the LAN911x Linux Driver The following sections can be found below * Revision History * Files * Features * Driver Parameters * Rx Performance Tuning * Tested Platforms * Rx
ButterFly4
- 蝴蝶效应展示 计算x=Rx(1-x),获得周期 鼠标拣选 将屏幕打印输出到BMP图像. 非线性动力学作业
Rx
- CC1100做呼叫器的程序(C语言)用8051与CC1100接口,语音压缩,频率在916.5MHZ
Infrared-RX
- 用单片机接收红外线IC发出的信号,汇编语言格式。
lcd_module
- verilog code which receive from uart RX and then output to lcd text display.
qqdengjijisuan
- 自己做来玩的,用来计算跟朋友QQ等级时差的小东西。用了suiPackt和RX控件。图片是定死的,懒得写自动生成代码,有兴趣的朋友可以自己改进
OFDM-basedWirelessBroadBandSystemSimulator
- 基于OFDM的无线宽带系统仿真It contains mainly two parts, i.e. link-level simulator and system-level simulator. Link-level simulator focus on a single-cell single-user scenario, where signal is transmitted from tx, and estimated at rx. Comparing the differen
Alamouti
- The program simulates alamouti s code with abitrary no.s of rx. Performance analysis can be drawn. (BER vs SNR)
TX_RX
- 在c++builder环境下一个串口通信程序,包括界面的设计和串口通信函数的设计,实现了串口通信。在文件夹TX-RX中。
test05
- UART RX with simple logic flow to check the protocol correct or not. Important is that the logic flow.
905
- NRF905驱动代码 // The content of this struct is nRF905 s initialize data. // CH_NO=1 433MHZ Normal Opration,No Retrans RX,TX Address is 4 Bytes // RX TX Payload Width is 32 Bytes Disable Extern Clock Fosc=16MHZ // 8 Bits CRC And enable