搜索资源列表
step
- 步进电机微调程序,用于步进电机控制与检测。测试步进角度和自动计算机角度。-Stepper motor tuning program for stepper motor control and testing. Step angle and automatic computer testing point of view.
bujin
- 步进电机正反转,调速控制,C+protues仿真-Positive step motor, speed control, C+ protues Simulation
MotorKalman
- 步进电机的MATLAB仿真程序,采用了卡尔曼滤波,对定子电流进行估计,并估算出转子的位置和速度-Continuous time extended Kalman filter simulation for two-phase step motor,Estimate the stator currents, and the rotor position and velocity, on the basis of noisy measurements of the stator currents.
Step_motor
- DSP 2812 的步进电机控制程序 步进电机/延时不能太长,否则转得太慢 /延时也不能太短,否则频率太高不起转-DSP 2812 stepper motor control program stepper motor/delay can not be too long, or turn too slowly/delay can not be too short, or too high frequencies can not afford to turn
M8Driver
- 五相步进电机环形分配驱动程序。稍加修改也可用于两相四拍和三相六拍步进电机驱动。-step Motor Driver。
step
- 通过LPC1114来发板来实现对步进电机的控制,方便,易懂,已经调试成功。-To send through the LPC1114 board to achieve the stepper motor control, convenient, easy to understand, has been commissioning a success.
lcd1602C
- xl系列单片机实验仪演示程序 LCD1602显示 步进电机控制器速度方向圈数可调 LCD1602显示 步进电机控制器速度方向圈数可调 K1-启动与停止步进电机运行 K2-设定步进电机运行圈数 (1-20圈) K3-设定步进电机转动方向 K4-设定步进电机运行速度 步进电机的转速控制分16档,数字越小,转速越快。 7.5度步进电机;周期7.5×4=30度,电机转动一圈需12个周期 资源:p1.0-p1.3接反向器74ls14,输出后接步进电机 p3.7接小喇叭提供按键音, p1.4-p1.7接端口
xiandaikongzhililun
- 电力牵引电机控制,设计的目的是用MatLab得到系统的状态空间模型,计算系统的传递函数。并预测系统的阶跃响应,并判断系统是否能控和能观。-Electric traction motor control, is designed to be used MatLab system state space model to calculate the system transfer function. And predict the system step response and determine
step
- 步进电机控制综合实验-Integrated stepper motor control experiment
MotoControlProcedures
- 马达控制程序的设计(em78) PORT5输出动作的控制,而且外部接有一推动STEP MOTOR的电路。写一程序驱动STEP MOTOR。-The design of motor control procedures (em78) PORT5 output control action, and then there is a promotion of external STEP MOTOR circuit. To write a program-driven STEP MOTOR.
step1
- 步进电机的使用 1、步近电机的驱动 2、步近电机方向的控制(通过改变送电顺序 系统设计 1、本实验采用4相4拍步进电机,步进角为7.5-The use of a stepper motor, step motor driven nearly 2, step-by-step directions in recent motor control (by changing the order of power transmission system design 1, t
Step
- 基于TMS320F系列DSP的步进电机完全控制程序。-TMS320F series of DSP-based stepper motor control program.
@TMCM310
- 步距电机控制代码。可以在X,Y,Z三个方向移动电机。-This code is written to control step motor, which is important in some measurments where precision is critical.
Clip2Net
- 前两个模块完成电机旋转方向设定,激磁方式设定和定位角度的换算等工作,后一个模块用于对换算后的角度量编码输出-step motor Quartus II Control Computer in System
BUCK
- 电力电子直流斩波降压BUCK电路。广泛用于直流电机调速 开关电源-Step-down DC chopper power electronics circuit BUCK. Widely used in DC motor speed control
PCD4541DRIVER
- 用51写的PCD4541运动控制IC驱动程序-pcd4541 STEP MOTOR DRIVER ic c source file
step
- 步进电机多级控制 可以64级调节步进电机转速和正反转-Multi-level control of stepper motor 64 may be stepper motor speed regulation and positive
bjdj
- 单片机控制步电机 步进电机是机电控制中一种常用的执行机构,它的用途是将电脉冲转化为角位移,通俗 地说:当步进驱动器接收到一个脉冲信号,它就驱动步进电机按设定的方向转动一个固定的 角度(及步进角)。通过控制脉冲个数即可以控制角位移量,从而达到准确定位的目的;同 时通过控制脉冲频率来控制电机转动的速度和加速度,从而达到调速的目的。-Single-chip stepper motor control of step motor is a common electrical and me
Text3l
- 步进电机的单片机控制,可以控制电机的正反转,有开关控制-step motor control by AT89C51
step_motor11
- 使用芯片为TI公司的DSP2812。该程序用以完成对交流电机的控制,启动/止、正转/反转、加速/减速。-Using TI s chips for the DSP2812. The program for the completion of the AC motor control, start/only, is to switch/reverse, speed up/slow down.