搜索资源列表
graduation
- 多路温度巡检仪采用ctrtex-M3内核的微处理器stm32为主控制器,配合数字式温度传感器、NRF24L01无线模块、液晶显示屏、LED 、及按键等组成。DS18B20温度传感器采用单总线技术实现和stm32的通信。采用NRF24L01无线传输将设备一采集到的温度信息传递给设备二。设备二的CPU将接收到的温度信息与设定的报警温度进行比较,如果大于设定的报警温度则亮对应的LED灯,并温度信息显示到TFTLCD屏上实现人机交互信息传递。按键的作用是设定设备一和设备二:如果 KEY1键按下,设置该
chengxudaima
- STM32控制板(自己设计的),主要实现的功能包括:GPS数据获取,LED显示,开关中断,数码管,USB(采用串口RS232协议,电路中设计了相应转换),霍尔传感器输入,SPI存储,FLASH扩展,继电器和实时时钟等功能的具体代码。通过编写具体的库,给大家做一个参考(注:都是底层的代码,库文件编写,针对电路的) 不含上位机部分-STM32 control board (own design), the main features include: GPS data acquisition, LE
chumoanjiantiaoguang
- 基于STM32开发板上有D1-D4四个LED灯,通过摇动全向摇杆改变模拟电压信号,在STM32中转换为数字量,STM32输出PWM波进而控制小灯的亮暗。 -Touch adjust light
LED_Matrix-2
- 64*32点阵驱动(STM32),通过行扫描同时发送行数据形成一个动态显示的内容-64*32 dot matrix LED driver(STM32)
stm32f746_ADC
- 本例介绍如何使用ADC3和DMA,从ADC3到存储器不断传输转换后的数据。 该ADC3配置为连续转换ADC_CHANNEL_8。 每次转换结束时的DMA传输,在循环模式下, 从ADC3 DR转换后的数据注册到uhADCxConvertedValue变量。 该uhADCxConvertedValue读值编码为12位,VREF +基准电压连接 在董事会到VDD(+ 3.3V)时,Vref-之间的参考电压连接在电路板到地面。 要转换的电压读取值,这里是方程适用
lanya
- STM32单片机通过蓝牙控制小灯闪烁,以实现人与小灯交互功能-Use bluetooth through stm32 to control a led
stm32f103-key-button---
- (STM32F1O3 芯片 软件使用Keil 包含了STM32 的所有外设库函数,可用于实际项目应用)程序包含操作GPIO口的使用,可用于其它程序的扩展。按下面板的上下左右键,串口会打印出键值,并点亮对应的LED。-(STM32F1O3 chip contains all the software using the Keil STM32 peripherals library functions can be used for the actual project application) u
template
- 基于MDK为stm32开发的示例工程,该工程中控制GPIO以推挽输出的方式控制相连的led的点亮与熄灭。-a template project based on MDK for stm32f103 with GPIO control
STM32F103_LED
- 讲述了STM32从建立工程,到点亮LED -About the project the establishment STM32, to turn on the LED
SIM900A-UDP-silent
- SIM900A UDP例程。使用UDP通信来控制开发板上的LED。-Use sim900a creat udp connect.use udp chain control LED which are on the STM32 board.
c
- 用STM32单片机实现I2C通讯,进行数据储存和保存操作,按键控制子程序,LED驱动子程序,PWM输出子程序等-STM32 MCU with I2C communications, data storage and saving, key control subroutine, LED driving subroutine, PWM output subroutines
GPIO_led
- stm32f103 流水灯程序实例,使用stm库把led灯点亮-stm32f103 led light program, just light up led by stm32 lib
paomadeng
- 通过STM32的IO口的高低电平控制,实现经典的跑马灯实验,控制两个LED交替闪烁。-Let the led light twinkle one by one by controlling IO of STM32 s IO .
HC_SR04
- STM32 KEIL5 实现LED灯的循环依次亮灭-STM32 KEIL5 implementation cycle in turn bright LED lights
key-polling
- 基于stm32程序,按键扫描,控制led灯反转-It s a keypolling procedure controlled by stm32 to make the led trigger
43254DFASDA
- STM32项目实战按键检测和LED控制例程功能实现代码,对于初学者来说,是有非常的帮助效果的-STM32 project combat key detection function and LED control routine implementation code, for beginners, it is very help effect
FreeRTOS_STM32F1xx_AlientekWarShip
- STM32移植FreeRTOS,演示3个任务,分别控制GPIO驱动的LED-STM32 transplant FreeRTOS, demonstrate 3 tasks, respectively, to control the LED
uCOSII_v2.91
- 代码是在STM32上移植的ucosII,ucos版本号为2.91。移植后有简单LED显示,可作为ucos研究的模板使用。-Code is on the STM32 transplant ucos II, ucos version number is 2.91. After transplantation simple LED display can be used as a template to use ucos research.
active3-rpi-hub75-adapter-fab
- STM32 Hub75 RGB LED Control
user
- 在STM32开发板上实现19264(不带字库)和BC7276控制的键盘显示,内含delay.c(原子延时)、key.c、led.c、还有字库文件,在KEIL MDK5验证可用-In the STM32 development board 19264 (without fonts) and BC7276 control keyboard and display, containing delay.c (atomic delay), key.c, led.c, as well as font fil