搜索资源列表
09.触摸键盘控制LED流水灯
- 单片机STM8S控制触摸键盘控制LED流水灯(Single chip microcomputer control touch keyboard to control LED flow lamp)
智能开关新技术项目程序文件
- Joshua 智能开关新技术项目 基于无线自发电开关 2016(stm8s develop Radio spontaneous electricity Joshua commit in 20180326)
dc-STM8S_Demo
- STM8S的调节电位器改变PWM波占空比的程序，库函数的版本。(The version of the library function that the STM8S adjusts the potentiometer to change the duty ratio of the PWM wave.)
ST8 for I2C
- stm8s I2C和ad采集例程，已调试可执行(Stm8s I2C and ad collection routines)
Stair Controller
- control light for stair up and down
I2C_Master
- funny the I2C_PECR is documented in STM8S103F3 specification while the Packet Error Checking is not part of the S family
STM8&DHT11
- STM8读取DHT11温湿度传感器的数据(STM8 reads the data of the DHT11 temperature and humidity sensor)
STM8S-W12T
- 利用STM8 编写W12T芯片基本驱动及编程，W12T为对讲机专用芯片(Using STM8 to write the W12T chip's basic driver and programming, W12T is a special chip for intercom.)
STM8S003F3P6开发板
- STM8S003LED流水灯源码以及串口通讯源码(STM8S003LED flow lamp source code)
main
- 串口发数据,速度为192000K，寄存器操作方法，测试已成功(Serial port send data, speed is 192000K, register operation method, the test has been successful.)
锂电池BOOST 充电电路程序IAR格式
- STM8S103寄存器版本BOOST升压电路程序，亲测可用，包含按键和数码管显示以及PWM和ADC采集！(STM8S103 register version BOOST step-up circuit program, pro test available, including buttons and digital display, as well as PWM and ADC acquisition!)
STM8从入门到精通V1.0
- STM8 单片机是意法半导体于 2009 年推出的一系列基于先进的 STM8 内核的 8 位单片机，它具有 3 级流水线架构、性价比高、开发方便。根据应用场合的不同，STM8 单片机主要分为 3 个系列：STM8S、 STM8L、STM8A。学习学习学习,入门学习stm8(Introduction to learning stm8)
stm8s_IAP
- stm8 x-mode iap bootloader
stms903k BLDC software
- 普通的无刷电机程序，基于stm8s单片机电机库的无刷电机控制程序，经过移植得到的较为简洁的程序。(The ordinary brushless motor program is based on the brushless motor control program of the stm8s single chip motor library.)
TM1680显示代码STM8平台.
- 以STM8控制TM1680,iic通信代码，数码可以显示，简单参考。(STM8 control TM1680, IIC communication code, digital display, simple reference.)
STM8S_008_WDG独立看门狗和窗口看门狗 - CSDN博客
- STM8S_008_WDG独立看门狗和窗口看门狗(stm8s_008 wwdg document)
6 BLDC 开环调速
- 此程序是用于BLDC电机驱动的，单片机是STM8S系列的单片机(this codes is used for the BLDC MOTOR DRIVER the MCU is STM8S series)
STM8S003F IO口模拟串口源码
- STM8S003F只有一个串口，项目中需要两个串口，因此采用IO口模拟一个串口。 此程序也是经理给的，经过测试可以用，不过需要耐心阅读一下程序，理解串口程序的思路，能够正确读写串口温度传感器的温度值(STM8S003F has only one serial port, and two serial ports are needed in the project, so IO port is used to simulate a serial port. This program is also
rV04-udiRC-20161009-SPI3-PUDN
- XN297L开发的遥控手柄，3线SPI发射，用此手柄作为四轴飞行器的遥控，可遥控四轴，也可回传四轴的各种数据。 在上电时选择工作模式， 默认TX,按住MODE键上电进入RX模式，连接串口使用地名站观察数据； 手柄硬件为STM8S+XN297L。(The hardware of the handle is STM8S+XN297L.)
STM8S-A10_I2C读写EEPROM（硬件）
- 硬件方式读取eprom，移植性强Hardware read eprom, portability(Hardware read eprom, portability)