搜索资源列表
shuzidianweiqi
- 制作的电源小程序，包含数字电位器调压，步进调压，已经使用过，初学者可以参考学习。一起进步。-Small power production procedures, including digital potentiometer voltage, stepper regulator has been used, beginners can refer to learn. Together with progress.
ZBzhongduan
- 开关电源稳压程序，采用dsPIC30F3011单片机作为系统的控制核心，输入直流电压100V，输出直流电压12V，其他电压等级的可采用类似方法。该程序是主题控制程序，其他外围程序会在后续更新中。-Switching power regulator program, using dsPIC30F3011 microcontroller as the control system, the input DC voltage 100V, output DC voltage of 12V, can be
helpers
- Voltage Current Regulator framework helper functions for Embedded Linux.
Battaries
- Standalone Photovoltaic (PV) system requires a proper battery charge controller. In this paper an efficient battery charge controller using Buck-Boost regulator with Maximum Power Point Tracking (MPPT) is presented. The voltage command is det
DC-motor-with-Buck-booster
- It acts in this TP of the regulation the speed of a D.C Motor with separated excitation, supplied with a chopper series, by using a regulator of the Proportional-Integral type (PI). The chopper is a static inverter allowing, starting a source of vo
s2mps11
- Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator.
simple-panel
- power-supply: regulator to provide the supply voltage.
imx53-pinfunc
- Maxim MAX8997 Voltage and Current Regulator.
shanbiantiaoya
- 电压闪变调压程序，simulink仿真，可看到具体过度过程。-Voltage flicker regulator program, simulink simulation, you can see over specific process.
test6050
- 瑞萨单片机和MPU6050通信测试通过，模拟IIC非硬件IIC 关于陀螺仪6050需要注意以下问题； 1、 IIC数据和时钟需要上拉电阻，电阻的大小与波特率有关，如果通讯不上适当减小波特率。 2、 6050供电电压为3.3V，请确认MCU电压和6050电压是否一致。 3、 MCU和6050最好用两个稳压芯片供电，要不MCU可能会干扰6050. 4、 需要用中断口11 5、主程序里有说明，当进到if(OK==get_mpu6050_mode()) { //此时可
Data_statistic_analysis_txt
- 代码为一个低压差线性稳压器的输出电压的统计分析，给出了输出电压在不同范围的统计分布-Change the code to a low-dropout linear regulator output voltage of statistical analysis, given the statistical distribution of the different output voltage ranges
HDC3A-Q
- 基于51单片机的电流互感器测试仪，驱动电动调压器输出测试电压-Based on 51 single-chip current ransformer tester, test drive the electric regulator output voltage
Grid-Connected-PV-Array
- Two demos illustrate use of SimPowerSystems for modeling a PV array connected to a utility grid. PVarray_Grid_IncCondReg_det.mdl is a detailed model of a 100-kW array connected to a 25-kV grid via a DC-DC boost converter and a three-phase three-lev
2011050601
- 龙科三相可控硅移相调压器资料，本人用于15kw电阻炉pid调压控温，很好用-Ronco three-phase SCR regulator, I used 15kw PID voltage resistance furnace temperature control, very good use
TPS65286
- 双路开关电源4.5V to 28V输入，6A输出-TPS65286 Dual Power Distribution Switches With 4.5-V to 28-V Input Voltage, 6-A Output Current Synchronous Buck Regulator
ac
- This circuit uses the AC7 block of SimPowerSystems™ library. It models a brushless DC motor drive with a braking chopper for a 3HP motor.The permanent magnet synchronous motor (with trapezoidal back-EMF) is fed by a PWM voltage source inverter,
three-phase-PWM-rectifier
- 提出了一种无电流传感器的三相 PWM 整流器控制策略。系统采用双闭环控制，外环 PI 调节器控制直流侧输出电压，内环通过滞环调节器控制有功功率和无功功率，达到单位功率因 数运行的目的。根据整流器的数学模型通过电流重构可获得网侧电流，以实现无电流传感器控制。 仿真实验证明该方案具有良好的控制性能。-In this paper a current sensorless control strategy of three-phase PWM rectifiers is presente
AC220V-DC4.2V
- 本设计设计手机充电器系统，实现由交流220V电能到直流4.2V电能的转换，进而为手机等设备充电。在系统控制中采用了变压、整流、滤波、稳压、分压、电压检测等电路，并且具有一定的充电提示和充满电自动断电的功能。 本设计采用Proteus（V7.1）软件仿真进行演示。-Based on Proteus simulation design phone charger system, implemented by 220V AC power to DC 4.2V power conversion. I
Car_PID
- 汽车PID调节，调节转速，力矩，电流，电压检测-Automotive PID regulator, adjust the speed, torque, current, voltage detection
MP2307
- MP2307,电源电压基准芯片，电源电力电子领域常用芯片。-MP2307，a monolithic synchronous buck regulator. The device integrates 100mΩ MOSFETS that provide 3A of continuous load current over a wide operating input voltage of 4.75V to 23V. Current mode control provides fast