搜索资源列表
CC2530WDTest
- 看门狗设计，也是信号采集系统的一部分，能够设置参数进行控制-Watchdog design, signal acquisition part of the system, the ability to set parameters to control
wtd
- MSP430 单片机基础运用，看门狗定时功能，适合参赛，模块化-MSP430 microcontroller that base, the watchdog timer function, suitable for competition, modular
Family-guard-system-based-on-GSM
- 本系统采用单片机作为控制中心，配有移动通信模块、警情采集电路、看门狗电路、声光报警电路和电源模块。当警情采集电路采集到警情信号时，单片机立即接通报警驱动电路实现声光报警，与此同时单片机接通移动通信模块，通过无线调制解调器接入GSM向外界报警，从而完成自动报警。-The system uses microcontroller as a control center, equipped with a mobile communication module, alarm acquisition cir
WDT
- 基于TMS5509DSP开发板的看门狗程序WDT-Based on TMS5509DSP development boards Watchdog program
WDT
- 基于mini2440 WINCE 5.0的看门狗驱动程序，内附详细的代码编译说明-Based on the the mini2440 WINCE 5.0 Watchdog driver, included a detailed descr iption of the code is compiled
WDT
- 看门狗定时刷新数码管程序，见详情，调试成功。初学者。-Watchdog timer refresh the digital control program, see the details of successful commissioning. Beginners.
CC430-3-WDT
- CC430看门狗控制程序并控制P2.7P2.6端口LED灯显示单片机处于睡眠状态。-CC430 watchdog control procedures and control P2.7P2.6 port LED lights display the MCU is in sleep state.
arm11_s3c6410_program_note.tar
- 基于arm11架构的s3c6410处理器的编程笔记（GPIO、INTERRUPT、CLOCK、WATCHDOG、PWM、DDR、NAND、LCD、ADC、DM9000）-Based on the the arm11 s3c6410 processor architecture, programming notes (GPIO, INTERRUPT, CLOCK, WATCHDOG, PWM, DDR, NAND, LCD, ADC, DM9000)
arm11_s3c6410_program_module.tar
- 基于arm11架构的s3c6410处理器的模块程序（GPIO、INTERRUPT、CLOCK、WATCHDOG、PWM、DDR、NAND、LCD、ADC、DM9000）-Program based on the the arm11 architecture s3c6410 processor module (GPIO, INTERRUPT, CLOCK, WATCHDOG, PWM, DDR, NAND, LCD, ADC, DM9000)
kmg
- STC12C5A60S2看门狗功能，如何自动重启。-STC12C5A60S2 watchdog function
C8051F31x
- C8051F31X 示例程序,可直接在开发板上运行 共13个 有ADC,Blinky,Comparators,Header_Files,Interrupts,Oscillators,PCA,PortIO,SMBus,SPI,Timers,UART,Watchdog-C8051F31X sample program can be run directly on the development board 13 ADC, Blinky, Comparators, Header_Files, Inte
kanmengou
- 51单片机看门狗程序，不错的代码，可以参考-51 single-chip watchdog program, good code, you can refer to
SPI_DAC
- 采用CPU Timer0产生定时周期50ms，输出锯齿波使能看门狗，在主函数中刷新计数器-The CPU Timer0 timing cycle of 50ms, the output sawtooth enable the watchdog refresh counter in the main function
MSP430G2xx3-Code-Examples
- 含有msp430G2553所有例程，包括基础时钟、定时器、ADC、看门狗、比较器、串口通信等等。适合初学单片机的朋友-Contain all msp430G2553 routines, including the base clock, timer, the ADC, watchdog timer, comparators, serial communications, etc.. Suitable for beginners microcontroller friend
AAT89S52_WDTT
- 用汇编写的AT89S52看门狗程序，此程序简单使用，能很很好的解决程序跑飞问题。-自动翻译， -Written in assembler AT89S52 watchdog program, this program is simple to use, the runaway programs can be a very good solution.- Automatic Translation
u-boot-1.1.1-ppc
- uboot-ppc源代码： 将uboot 移植到ppc处理器mpc8247/mpc8260/mpc8270上，命令丰富、设备驱动详尽（包括SDRAM、NOR Flash, NAND flash, serial, timer, watchdog等等),对学习理解ppc处理器和板卡很有帮助。 -uboot-ppc src: implemente uboot in ppc processor mpc8247/mpc8270/mpc8260。It has a lot of commands, a
STC89C52andX5045
- STC89C52源代码，功能主要包括：看门狗、键盘、数码显示，通信控制。-STC89C52 source code, functions include: watchdog, keyboard, digital display, communication control.
WDT-500013
- 本应用介绍了如何使用监视定时器。 本应用描述了监视定时器的功能并举例说明。-* THIS SAMPLE CODE IS PROVIDED AS IS AND IS SUBJECT TO ALTERATIONS. FUJITSU*/ /* MICROELECTRONICS ACCEPTS NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR*/ /* ELIGIBILITY FOR ANY PURPOSES.
kanmengou
- mega16 看门狗实验 proteus电路仿真-and mega16 watchdog experimental proteus circuit simulation
ADC_AnalogWatchdog
- ADC看门狗程序，用于ADC看门狗的关断和监控检测-ADC Watchdog procedure.Generation for ADC watchdog and shutdown detection, is a good ADC Watchdog program