搜索资源列表
MAX232
- 单片机串口通信程序,内附protues模拟,可以实现单片机间串口通讯-Single-chip serial communication procedures, and inserting protues simulation, can achieve single-chip serial communication between
Serial
- 采用C++ Builer编的一个串口通信源码,通过虚拟串口在电脑上模拟两个串口并连接,可以很方便的调试和学习串口编程。-Using C++ Builer made a serial communication source, through the virtual serial port on the computer simulation and two serial connections, can be very convenient to study serial debugging a
Virtual_COM_Port
- USB模拟串口通信的例子,适合于STM3210E的学习板.-USB serial communication example of simulation for learning in STM3210E board.
123321123
- holtek h48c70 将I\O模拟串口使用。-holtek h48c70 will I \ O simulation using the serial port.
C51_COM
- 用51系列单片机IO口模拟串口通讯C源程-51 Series single-chip microcomputer with analog IO I-way serial communication C source
51COM
- 用51单片机I/O口模拟串口通信,在较低的比特率下能有较好的通信效果,尤其在单片机串口不够用时,模拟串口是很好的解决方法。-With 51 single-chip I/O port simulation of serial communications, at a lower bit rate to have better communication effects, especially in single-chip serial port when not enough to simulat
uart(300bits)
- (小邢)IO模拟串口(300bits),非常稳定可靠.调试通过.-IO serial analog (300bits), very stable and reliable. Debug through.
2602IC_RCTEST
- sonix SN8P2602单片机例程,模拟串口,按键扫描,LED驱动-sonix SN8P2602
SnSetup
- 虚拟串口小程序,可以模拟最大254个串口,为那些电脑没有串口的用户,和串口少的用户提供方便,界面简单-Virtual Serial Port applet, can simulate the largest 254 serial, serial for those who are not computer users, and the serial port to facilitate users with a small, simple interface
VSerial
- windows下的虚拟串口驱动,可以虚拟出串口,用于模拟通信。-windows under a virtual serial port driver, the virtual serial port can be used for analog communications.
ircom
- 该程序时在c51单片机在遥控解码通过电脑串口显示,在电脑上显示出遥控的按键, 程序中是模拟红外接收时序,可接受很多种遥控器的信号 对大家 红外遥控的学习很有用-C51 when the program in single-chip decoder via the computer serial port remote control indicates that the computer shows that the remote control button, the progra
M88(9600Bps)
- AVR单片机M88实现的模拟串口(9600Bps),已经在多个项目中应用,可靠性高,很有价值的一种用法!-M88 single-chip realization of AVR serial analog (9600Bps), the project has been implemented in many applications, high reliability and a valuable use!
NXPsoftwareUARTforLPC2000
- NXP公司写的模拟串口程序,功能全面,很强大-NXP' s serial port to write the simulation program, full-featured, very powerful
msp430shujucaijixitong
- msp430f149实现的数据采集系统 结构简单 功耗低 模拟采集传感器 数字开关量采集 串口通讯UART模块 电源供电及复位-Executable files built outside of IAR Embedded Workbench Follow these steps to load and debug an executable file that was built outside IAR Embedded Workbench, for example p
11714318751IO_SOFT_UART
- 基于89S51的IO口模拟串口通信,调试通过。-89S51-based simulation of the IO port serial communication, debugging through.
m_usart
- PIC单片机模拟串口收发.可设置波特率。8位9位可选-PIC microcontroller analog serial transceiver. You can set the baud rate. 8 9 optional
mcu_51_io_uart
- 51单片机IO口模拟串口通讯C源程,适用于AT89S51/AT89S52等单片机。-MCU GPIO uart c source code ,can use for AT89S51/AT89S52 etc.
bright
- PIC16c57 Bright embedded control module模拟串口通信部分-PIC16c57 Bright embedded control module
PLCWork
- 一台电脑上,没有实际的串口设备,只需要安装虚拟串口,再用这段小程序,就可以对电脑VBA程序进行调试了。 这段程序实际上是在一个专门的ExcelVBA文件模块里,模拟外设,与主程序ExcelVBA进行呼应。-A computer, there is no real serial device, only need to install a virtual serial port, and then this little program, you can debug a computer pr
adcmeter
- 基于 CS5550 工业测量仪表的设计:ADCMeter.ddb 中包含电路原理图和样品PCB图。本系统以 STC 系列 51 单片机为控制核心,使用高精度 CS5550 A/D 芯片来采集微弱的模拟信号量(如热电偶,热电阻信号量),可在线校准(零校准,满量程校准),校准数据保存到 93C46 中,作为以后 CS5550 运行的校准参数。本系统还包括两行八个数字位的数码管实时地显示采集数据,并可通过板上按键输入,进行输入信号变换的切换。另外还可增加串口通信部分,将采集的数据传输给上位机或其它控制