搜索资源列表
C8051F020实现ADC采样芯片外
- C8051F020实现ADC采样芯片外的模拟电压,通过LCD显示,并通过串口发送到PC机(C8051F020 analog chip to achieve analog voltage outside the ADC, through the LCD display, and sent to the PC through the serial port. Required Downloads)
IOUSART
- PIC单片机io模拟串口19200的实现(PIC microcontroller IO analog serial communication program 19200)
MSP430BSL_1_00_12_00
- 在芯片没有充足USCI模块的情况下,用普通串口和定时器A实现UART功能(Using serial port and timer A to realize UART)
new_simulation
- 通过时钟使普通的IO口模拟UART串口通讯(Use Timer_A CCR1 hardware output modes and CCR0 SCCI data latch // to implement UART function @ 2400 baud. Software does not directly read and // write to RX and TX pins, instead proper use of output modes and SCCI data // la
STM32F107虚拟串口USB转串口
- 虚拟串口,使用STm单片机实现虚拟串口,模拟串口调试等等。该源码为官网下载(Virtual serial port, the use of STm MCU virtual serial port, analog serial debugging, and so on. The source code for the official website download)
serial-STM32-gai
- 上位机通过串口控制STM32,STM32模拟红外协议输出(The host computer controls the STM32 through the serial port, and STM32 simulates the infrared protocol output)
SW_uart_Temp
- 利用单片机普通IO口模拟串口接收和发送。(MCU common IO port analog serial port to receive and send.)
PCF8951四路采集串口显示源代码
- PCF8951四路模拟量的串口显示与调试(Serial display and debugging of PCF8951 four way analog quantity)
comKbd
- 串口键盘模拟程序,从串口扫描枪读取数据并模拟键盘录入。 采用winio模拟,未解决x64平台下加载问题。 半成品,慎用(Serial keyboard simulation program, read data from the serial scan gun and simulate keyboard input. Using WINIO simulation, the loading problem of x64 platform is not solved. Careful use
Simalator
- 用来模拟串口发送接收 主要接受卫星相关数据(Using the analog serial port to send and receive)
STM8_模拟串口接收(接收单个字节完成)
- 利用STM8S103F3P6的普通IO口设计UART功能,波特率可以达到250Kbps,能够稳定的接收单字节数据并通过串口输出。模拟串口的发送也可以达到250Kbps.(Using STM8S103F3P6 general IO mouth design UART function, baud rate can reach 250 KBPS, can receive stable single-byte data and output via a serial port. Simulation
HT66F2390_UART_1602
- 这是合泰HT66F2390的模拟串口完成程序包(This is the complete serial simulation of Thailand HT66F2390 package)
SoftWareSerial
- STM32 IO模拟串口 发送接受 波特率9600(STM32 IO Analog serial port to send acceptance.)
P3.3 C#SerialPort
- 模拟两个串口进行通信,备注齐全。(Serial communication)
电位器AD并串口通信(8位)
- 利用xpt2046的ad转换功能转换电位器的模拟量,晶码管显示并通过串口通信发到电脑,利用串口调试助手显示数据(The analog converter of potentiometer is transformed by xpt2046's AD conversion function. The crystal code tube is displayed and sent to the computer through serial port communication, and the d
端口调试工具
- CommMonitor 侦测、拦截、逆向分析串口通信协议, 是侦测RS232/422/485串行端口 的专业工具软件,是软硬件工程师的最佳助手。CommMonitor 能侦听、拦截、记录、分析 串行通信协议,让您对应用程序操作串行端口的过程和细节,让您及时的模拟被侦听程序 或设备的数据、控制流,提高工作效率。(CommMonitor detects, intercepts, and analyzes serial communication protocols in reverse. It
mega48 模拟串口
- Mega48单片机,8M晶振; 使用IO口模拟串口接收的程序(Using the IO port to simulate the program received at the serial port)
SPComm触发器
- 需要安装spcom控件,提高串口4针和7针进行输出,可以模拟触发电平,启动或停止工业设备,如变频器的运行和停止。(Need to install SPCOM controls, increase the serial port 4 and 7 needles for output, can simulate the trigger level, start or stop industrial equipment, such as the operation and stop of the fr
HT66F002test
- 在单片机上模拟了一个串口,使用pa5作为发送端 * 把单片机中存放的数据通过pa5作为串口TXD发送出去(A serial port is simulated on the MCU, and Pa5 is used as the transmitter. * send data stored in SCM by Pa5 as serial TXD.)
SoftUart
- 硬件平台:基于stm8l052r8;使用IO口模拟串口。(Hardware platform: based on stm8l052r8; use IO port to simulate serial port.)