搜索资源列表
IO_SOFT_UART_USE_TIMER
- 1. 本程序使用一个定时器和任意 2 个 I/O 口模拟一个串行口。 2. 1位起始位,8位数据位,1位停止位。发数据位时先发低位。 3. 支持半双工通讯。收、发波特率相同。 4. 应把定时器中断优先级设置为最高级。 5. 本程序每接收一个字节后就把它放到一个队列缓冲区中(也可使用环行缓冲区), 待缓冲区满后,将缓冲区中的内容原样发回。这是为了测试多字节连续收发的 能力和简化程序。实际应用中应防止缓冲区溢出。 6. 由接收转换到发送时要先调用 sof
sci-a.rar
- TI F28335 的串口通讯程序;以测试过,可以放心使用。,TI F28335 Serial Communication procedures to test, and can be assured that use.
test_VB.rar
- GSM模块测试小程序。自动换通讯波特率测试串口,读SIM卡测试,信号强度测试。,GSM module test applet. Automatically for the serial communication baud rate test, reading test SIM card, the signal strength test.
COM
- c# 串口通讯 下面是串口通讯测试程序的源代码,将mycom类放在此项目中 可以实现简单的串口通信,希望读者能通过这个程序对串口通信过程有一个初步的了解-c# COM Communcation
HT-C-example.rar
- HT系列掌机部分功能测试程序(含源码),包括以下几个部分:串口通讯,红外通讯,菜单,液晶测试,文件处理程序,支持掌机:HT1600,HT2600,HT2680A,HT2680,HT2800 ,HT Series portable part of the functional test procedures (including source code), including the following sections: serial communications, infrared comm
0555
- 51单片机串口通讯设计代码公开, //这是一个单片机C51串口接收(中断)和发送例程,可以用来测试51单片机的中断接收 //和查询发送,另外我觉得发送没有必要用中断,因为程序的开销是一样的 -51 design code serial communication open,// ??this is a C51 microcontroller serial receiver (interrupt) and send routine can be used to test the mi
cn537048
- DSPIC33 的串口通讯程序,直接应用在dspic33上的通讯测试程序,波特率自动设定-dspic 33 serial comunication demo
STC12C5A60S2-and-VS1838B-UART
- 基于单片机STC12C5A60S2和红外线接收器VS1838B的红外线解码测试程序,内含两个程序,分别是单片机程序及VB6上位机程序,通过串口进行通讯-Microcontroller based infrared receiver VS1838B STC12C5A60S2 and infrared decoder test program that includes two procedures, namely, single-chip program and VB6 PC program to
gyro
- 利用invensense公司的最新MPU-6050来测试陀螺仪数据和加速度数据,并在电脑串口显示出来。本程序的独到之处是增加了一些在串口上显示单片机执行指令的代码并显示MPU-6050的应答信号,以此更清楚地弄明白MPU-6050的通讯过程-Using invensense latest MPU-6050 to test the gyro data and acceleration data, and the serial port on the computer display. The un
vc
- 关于VC编写的一份串口通讯程序,测试已通过-VC prepared on a serial communication program, test has passed
TYServer
- 关于VC编写的一份串口通讯程序,测试已通过-VC prepared on a serial communication program, test has passed
SPCE3200LABCODE_16to23
- 凌阳SPCE3200 系统开发板随机自带源程序。共安排了32个子目录,其中按照SPCE3200实验指导书(上册)中的实验顺序存放了实验程序的源代码,所有项目代码均在S+coreIDE v2.1.2下测试通过。此为第16到第23个试验源代码。试验内容如下: 5.3 实验十六:Cache 读写实验. 5.4 实验十七:DMA读写实验 5.5 实验十八:SD卡读取实验 SPCE3200教学平台通信模块实验 6.1 实验十九:SPI通信实验 6.2 实验二十:I2C通信实验.
TestCom
- 一个有关串口通讯的小程序,主要测试从串口处接收方面.-A serial communications applet, the main testing area from the serial receive.
MSP430F449
- MSP430F449演示程序:ASCII显示,串口通讯测试,定时器TA,发光二极管闪烁,发声演示,蜂鸣器,键盘程序,流水灯-MSP430F449 Demo: ASCII display, serial communications testing, timer TA, blinking light-emitting diodes, audible demonstration, buzzer, keyboard procedures, water lamp
willar_350993
- 串口测试程序,方便初学者调单片机串行通讯 -12333333333
serialforavr
- 主要是配合avr单片机的一个测试程序,里面有串口通讯,和listiew潜入控件-Mainly avr microcontroller with a test procedure, there are serial communications, and control into listiew
HZTableComHelp
- 这是本人的一个正式项目中所做的测试工程源码。主要功能是通过串口与板子的GSM模块进行通讯,进行收发短信的程序。内容有:串口设置,GB2312与UNICODE编码转换,PDU编解码(此部分大部分借鉴了网友的代码),AT指令发送。完全可以将相关代码移植到嵌入式短信收发设备中去。我的相关嵌入式项目也确实是在这个基础上做的。-This is my project done by a formal evaluation of the source. Main functions of the board
FunnComHelp
- 是本人的一个正式项目中所做的测试工程源码。主要功能是通过串口与板子的GSM模块进行通讯,进行收发短信的程序。内容有:串口设置,GB2312与UNICODE编码转换,PDU编解码(此部分大部分借鉴了网友的代码),AT指令发送。因内部使用了MultiByteToWideChar、WideCharToMultiByte字符转换函数,所以不能直接向嵌入式程序中移植。想要做这方面移植的请参考与本人上传的另一个资源“ HZTableComHelp.rar”-Is my project done by a f
upload
- serial_44b0 44b0uclinux串口驱动程序-,Unix_Linux,嵌入式Linux U盘源码 基于MCU的U盘源码,实现flash的windos文件系统 temp3 温度传感器的单片机处理显示程序,已通过测试 USB2.0 USB2.0开发例程,基于51单片机,包括pc端程序 红外源程序 51单片机的一段C语言源程序,为NEC的源代码,可以在你做红外通讯时作参考 keil uCOS_II v2.70 port
RS232
- 很好的烧录程序,用于测试串口通讯信息,就是把一段代码烧录到单片机中,然后让它显示到电脑上!-A good burning program, used to test the serial communication of information, is to burn a piece of code to the MCU, and then it shows to your computer!