搜索资源列表
CPP_USB-CAN
- C++关于DLL调用的源代码,关于界面设计,DLL调用等方面,很有参考价值。此例程针对武汉吉阳光电www.glinker.cn的GY8507 USB-CAN总线适配器开发,二次开发例程。-C++ On call DLL source code, with regard to interface design, DLL calls, etc., could very well refer. This routine for the www.glinker.cn Wuhan Photoelectri
485PDS18B20(ATMEL89C2051)
- 485收发+DS18B20呼叫应答方式(ATMEL89C2051) 温度是工业生产中重要的物理参数之一,对其进行测量与控制是一项非常传统的工艺技术。采用数字温度传感器DS18B20和AT89C2051单片机进行温度数据的采集和存储,通过RS485总线传输。上位计算机对所测得的每个误差补偿量,依据误差回归模型的最小二乘法进行参数估计。做出线性误差补偿模型的数学方程,对常温下测量的数据进行了补偿处理,在-55℃到+125℃测量范围和测量精度0.2级下,实现传输距离达到500 m,并根据工程实践给
CPP_USB-CAN
- C++关于DLL调用的源代码,关于界面设计,DLL调用等方面,很有参考价值。此例程针对武汉吉阳光电www.glinker.cn的GY8507 USB-CAN总线适配器开发,二次开发例程。-C++ On call DLL source code, with regard to interface design, DLL calls, etc., could very well refer. This routine for the www.glinker.cn Wuhan Photoelectri
sim_i2c
- 模拟I2C总线驱动程序,只需要二根普通的GPIO即可-simulator i2c driver, just need 2 gpio pins
Search_ROM
- 利用二叉树的原理,在C中模仿单总线器件64位序列号的寻址。-Using the principle of binary tree, imitating addressing single bus device 64-bit serial number in C.
proteusP877APnet
- 基于proteus仿真试验环境下的pic16F877a单片机,组成的RS485总线的仿真程序.按下仿真中的铵钮开关一次,分机1号收到返馈并使能数码管,按二次,分机2号...,调试完成.-Based on pic16F877a MCU, proteus simulation test environment composed of RS485 bus simulation program. Press the push button switch of the simulation of a, e
实验三十二:工业总线485
- 485通信,使用库函数进行编写,已经验证可操作,另:使用uart1口(485 communication, using library functions)
sdram_16bit_latest.tar
- 这个IP核是一个小型的,简单的SDRAM控制器,用于为16位SDRAM芯片提供32位流水线的二叉树接口。 当访问开放行时,读写可以流水线实现完整的SDRAM总线利用率,但是读写之间的切换需要几个周期。(This IP core is that of a small, simple SDRAM controller used to provide a 32-bit pipelined Wishbone interface to a 16-bit SDRAM chip. When acce
实验三十二:工业总线485
- 实现RX485的通讯功能,基于stm8s单片机(485 communications, based on stm8s)
串口通信采集存储
- 串口数据采集RS232串口是工业中比较常用,也最容易接触到的一种总线协议,台式机上一般都有二个,而现在很多下位机、仪器等很多都还是使用串口通信的。通过RS232串口可以方便的实现Labview与其他测试软件、控制软件的通信。(Serial port data acquisition RS232 serial port is a kind of bus protocol which is commonly used in industry, and it is also the most easy