搜索资源列表
DS18B20basedon51c
- ds18b20做的一个温控程序,达到一定温度自动报警,单片机是51的,数码管显示-ds18b20 do a temperature control procedures to achieve a certain temperature alarm, the microcontroller 51, the digital display
lesson15
- 单片机控制数码管显示1—16的平方,通过按键控制输入数的大小,用C语言编写-SCM 1-16 square digital display by the number of buttons the size of the control input, using C language
part2.6_1
- 利用定时器产生一个0-99s变化的秒表 并显示在数码管上 每过一秒将这个变化写到AT24C02内部储存 再次上电时 单片机直接读AT24C02里的数据-Use the timer to generate a change in 0-99s and displayed on the digital stopwatch on this change with every passing second internal storage re-write AT24C02 microcontroller
szz
- DS1302和51单片机设计电子钟数码管显示(未作出防真)-MCU Design DS1302 and 51 clock digital display (not to prevent true)
74595控制数码管
- 通过15单片机控制74595芯片从而控制数码管显示数字,对管脚是一种极大的节约
单片机定时器实现秒计时和显示
- 1 基础部分: (1) 用51的p1口作为数据输出口,p2口为共阴数码管位选信号,利用定时器0实现秒计时和显示。 (2) 上电复位后,显示00。 (3) 按键按下S2键后开始计数。采用加法计数形式。计到60停止。蜂鸣器鸣响。 (4) 鸣响2秒后停止,恢复显示00。 (5) 当再次按下S2键后重复1-4过程。 2 提高部分: 利用S2,S4,S6完成进入设置;进行数字十位和个位设置;存储,启动等动作; 工作过程如下: (1)第一次按下S6,进入十位数设置;此时,每按下S4一次
8只数码管滚动显示单个数字
- 基于C51单片机,使用数码管滚动显示单个数字(Digital tube scrolling shows a single number)
7SEG LED segment
- 7段数码管显示程序PIC单片机,通过扫描显示,实现6位数码管显示,(7 segment digital display program, PIC microcontroller, through the scanning display, to achieve 6 digital display,)
3
- 数码管从1到F依次显示,同时伴随LED的亮灭。(Digital tube from 1 to F in turn show, accompanied by LED lights out.)
51单片机温度计DS18B20
- 基于51单片机的温度测量,数码管显示。实时监控环境温度(SCM temperature display)
红外通信-数码管显示
- 能实现接收红外遥控信号,并显示相应的字符。(Receive infrared remote control signal and display the corresponding characters)
单片机读取矩阵键盘并在4LED上显示按键值
- 单片机读取矩阵键盘并在4段数码管上显示按键值(SCM read matrix keyboard, and display button value in the 4 section of the digital)
133-热敏电阻测试数码管显示
- 单片机 NTC温度采集代码。(Singlechip NTC temperature acquisition code.)
51单片机动态数码管c程序
- 此文件用于51系列单片机的动态数码管显示C语言编程的参考代码
1oneten0to9
- 用软件延时的方法,经过循环嵌套实现数码管的显示间隔一定的时间,文本采用汇编语言书写,适用于keil(The project is set to control the delay time of led.All of the centenses are writed by asm language,and they are suitable for keil.)
zy
- 四位数码管动态显示,按键加减计数,原理图仿真,C51程序。(Four digital tube dynamic display, buttons add and subtract count, schematic simulation, C51 program.)
89C51矩阵按键数码管移位显示
- 用98c51单片机实现独立的矩阵键盘控制数码管移位显示功能(Using 98c51 MCU to realize the independent matrix keyboard control digital tube shift display function)
89C52单片机实用教程
- 采用STC89C52与DS18B20采集温度并显示至数码管,附有porteus仿真(STC89C52 and DS18B20 are used to collect temperature and display to digital tube)
基于单片机控制的交通灯
- 十字路口车辆穿梭,行人熙攘,车行车道,人行人道,有条不紊。那么靠什么来实现这井然秩序呢?靠的是交通信号灯的自动指挥系统。交通信号灯控制方式很多。本设计主要分为五大模块输入控制电路、时钟控制电路、片内外程序切换控制、显示电路。以MSC-51系列单片机IntelAT89C51为中心器件来设计交通灯控制器,实现了AT89C51芯片的P0口设置红、绿灯、黄灯燃亮时间的功能;为了系统稳定可靠采用了74LS14施密特触发器芯片的消抖电路,避免了系统因输入信号抖动产生误操作;显示时间直接通过AT89C51的P
数码管滚动显示
- 在51单片机上滚动显示hello字符 运用了数码管动态显示的原理,通过数组实现(Display Hello characters makes use of the principle of dynamic display of digital tube in 51 single scroll through array)