搜索资源列表
dht11
- 用51单片机控制dht11温湿度传感器的驱动程序 在数码管上显示 利用595扩展io口-With 51 single-chip driver control dht11 temperature and humidity sensors on the digital display 595 extended io port
74HC595_C51
- 用C51控制74HC595驱动LED数码管显示的例程-74HC595 drive LED digital tube display routines with C51 control
sht11
- SHT11温湿度传感器芯片和MAX7219共阴极数码管的驱动-the driver for SHT11 and MAX7219
0-9999
- 利用STC单片机驱动数码管进行字符显示的程序-STC microcontroller-driven digital control character display program
7219
- 基于MSP430F413控制的max7219数码管显示驱动例程-Based on MSP430F413 control max7219 digital display driver routine
STM32---LED
- STM32单片机实现8位数码管动态显示,使用了我自己编写的驱动。-STM32 MCU 8 digital tube dynamic display
dxf
- 基于51单片机的双步进电机综合控制原理本程序用于测试4相步进电机常规驱动 4个按键分别控制加速、减速、开启、停止 数码管显示 01-18速度等级,数字越大,速度越大-By 24L01 wireless module, remote control, car control program based on the stepper motor and STC89C52 microcontroller can be independently controlled to achiev
temp
- 驱动6个TM1629显示数码管的程序,可以显示100位LED-100 LED drive 6 the TM1629 show digital tube procedure,
CH452W2
- 按键及数码管显示驱动芯片,调试通过,有中文备注。CH452的真正2线接口,含低电平脉冲按键中断在内,只需要2个I/O引脚,兼容I2C/IIC时序 两线制方式SCL/SDA,按键中断由SDA产生,接单片机的脉冲/边沿中断引脚 对于频率低于24MHz的MCS51,为了节约传输时间,可以适当减少SCL/SDA之间的延时-Buttons and digital display driver chip debugging through, Chinese Remarks. Including
DSP2812aMAX7219
- DSP2812实现MAX7219驱动LG5641AH四位数码管程序,用来显示0~999,已测试,可用!-DSP2812 achieve MAX7219 drive LG5641AH four digital tube, used to display 0 to 999, have been tested, available!
AVR-PROTEUS
- mega16的基本程序(跑马灯、AD转换、外部按键中断、定时中断、范围选择、串口通信、驱动数码管、LCD1602),适合初学者的简单程序,附有proteus仿真图-mega16 the basic program (Marquee, AD conversion, external key interrupt, timer interrupt, range selection, serial communications, drive digital tube LCD1602), suitable
shiyan7
- 简易抢答器,开始时,接通拨码开关K1,通过单片机驱动数码管进行倒计10s(数码管显示9—0),倒计10s完毕后数码管显示横杠(-),此时,可任意接通四个抢答开关(K2,K3,K4,K5)其中一个来进行抢答,抢答完毕后,数码管显示抢答结果(即抢答开关号码),最后,K6给一个单脉冲,数码管进入新循环状态:倒计时,接着下一轮抢答。-Easy Responder, start, turn DIP switch K1, microcontroller-driven digital tube carried
Protues
- 基于Protues软件下的综合仿真 福利贴..........把这次自己整的单片机综合实验发出来分享下.........(含报告)... 1、掌握Protues硬件仿真软件的使用。 2、掌握单片机IO口输入、输出的控制。 3、掌握单片机定时器、串口等资源的控制。 4、掌握数码管动态显示的方法。 5、掌握用单片机驱动DA、AD芯片。 6、掌握用单片机驱动1602液晶、8*8点阵列屏。 一个工程包含所有功能.......包含源码-Based o
CH451
- ch451程序驱动键盘及数码管电路,希望对大家有用-the ch451 program drive keypad and digital control circuit, and hope to be useful
DS1302
- RTC实时时钟(DS1302) 驱动程序的编写以及实现数字字符在数码管中的显示-RTC real time clock (DS1302) preparation of the driver as well as the digital characters in digital tube display
LED
- 数码管显示驱动,74LVC595A,c8051f350-Digital tube display driver, 74LVC595A
yima
- 七段数码管的驱动程序,输入四位二进制码,输出七位数码管(低电平驱动)驱动代码-Segment digital tube driver, enter the four-bit binary code, the output of seven digital tube driver code
led
- 实验目的:理解LED七段数码管的显示控制原理,掌握数码管与MCU的接口技术,能够编写数码管显示驱动程序;熟悉接口程序调试方法。 实验内容:利用C8051F310单片机控制数码管显示器 基本要求: 利用末位数码管循环显示数字0-9,显示切换频率为1Hz。 提高要求: 在4位数码管显示器上依次显示当天日期和时间,显示格式如下: yyyy (年份) mm.dd(月份.日) hh.mm(小时.分钟)-The purpose of the experim
LT24l01_rx
- MSP430F149驱动24L01 使用MSP430F149的SPI0模块实现 发送过来的温度值,用数码管显示-The MSP430F149 driver 24L01 use MSP430F149 SPI0 module temperature value sent with a digital display
UCOSII_SPI
- LPC2114基于UCOSII的SPI驱动使用的例子。通过硬件SPI接口控制LED数码管显示数,中间件代码-LPC2114 SPI UCOSII the drive using examples. Hardware SPI interface to control the number of LED digital tube display, middleware code