搜索资源列表
GE PACE
- 用labview写的控制GE PACE的气压设备，可以读取GE PACE的气压值，并且有实时保存的程序，很好用(LabVIEW written with GE PACE control of atmospheric pressure equipment, you can read the GE PACE barometric value, and has a real-time save the program, very good use)
物性重调 点火
- FLUENT非稳态燃烧点火CASE文件，混合完成可以点火(Unsteady state combustion ignition)
微型气象站
- 平台为arduino uno r3，采集温湿度，气压、海拔、土壤湿度信息在5110屏幕上显示，并通过nrf24l01传到另外一个arduino采集板上，然后通过串口传给pc机。传感器有ds18b20，dht11，土壤湿度传感器，bmp085，显示屏为5110，一对nrf24l01。library文件夹下为所需的各种库。(The platform for Arduino uno R3, collecting temperature and humidity, air pressure, altit
基于STM32的气象站预报系统硬件设计原理图
- STM32的BME280小型气象监测台，用于监测温湿度与气压(BME280 meteorological monitoring of STM32)
bmp180气压检测
- bmp180 厂家资料，有示范程序，亲测可用。(Bmp180 manufacturers information, there is a demonstration program, pro test available.)
ms5805
- 温度气压传感器MS5805代码，含计算海拔高度(Temperature pressure sensor MS5805 code, including altitude)
51读气压计
- 基于51单片机的BMP085气压温度计，代码完整，可供参考(BMP085 pressure thermometer based on 51 single chip microc)
STM8L - BMP280
- STM8+BMP280采用SPI方式驱动，测量压强(STM8+BMP280 is driven by SPI to measure pressure)
20140915_方程式换挡
- 用飞思卡尔单片机MC9S12XS128编写的方程式赛车采用气压阀门换挡的程序。(The program is for the MC9S12XS128 microcontroller which used for the shift gear with air pressure valve in Formula car.)
DHT11,BMP180组合
- 采集温湿度气压加显示到显示屏上，采用STM32(Collecting temperature and humidity pressure to display, using STM32)
BMP280_IIC_SPI
- BMP280arduino驱动代码，适用于BMP280气压传感器(this is a BMP280arduino driver)
Stm32F407_Template_iar
- STM32F407的气压传感器MS5611控制程序(STM32F407's air pressure sensor MS5611 control program)
Characteristic in Moderate Pressure Used for D
- 中等气压下，微波等离子体放电的数值模拟。(Numerical simulation of microwave plasma discharge at medium pressure)
Glow discharge in low pressure plasma PVD- mat
- 直流辉光放电，低气压下辉光放电的数值模拟(Numerical simulation of microwave plasma discharge at medium pressure)
GY-65气压模块发送资料
- 使用BMP085气压计进行测量高度的源代码，包含arduino，51，avr三种(Use BMP085 barometer to measure the height of the source code, including Arduino, 51, AVR three kinds.)
bmp180
- iic总线方式读取数字气压传感器BMP180数据，数据显示到oled(IIC bus reads the digital pressure sensor BMP180 data, and the data is displayed to OLED.)
bmp180
- 气压值 温度值的检测 并通过该值计算当地的海拔高度(Detection of the temperature value of the pressure value)
计控实验胎压监测
- 本系统由胎压监测模块和中央监视模块两部分组成。胎压监测模块安放在轮胎内用于检测轮胎压力后经无线模块传输给位于车内的中央监视模块。胎压监测模块由控制器单片机，气压传感器和，电源模块和无线发射模块组成；中央监视模块由控制器单片机，液晶，声光报警装置，电源模块和无线接收模块组成。系统硬件框图如下。(The system consists of two parts: tire pressure monitoring module and central monitoring module. The ti
bmp180-noh
- esp8266通过I2C总线读取bmp180芯片的气压和温度值，不用库文件的代码。(Esp8266 reads the pressure and temperature values of the bmp180 chip through the I2C bus, without the code of the library file.)
MS5611_spi
- IO口模拟SPI与MS5611通信，使用GPIOB.3、GPIOB.6、GPIOB.4、GPIOB.5分别模拟主机的CS（片选），CLK（时钟），MISO（输入）、MOSI（输出），实现了与MS5611的通信。(IO port analog SPI and MS5611 communication, using GPIOB.3, GPIOB.6, GPIOB.4, GPIOB.5 to simulate the CS (chip) of the host, CLK (clock), MISO (