搜索资源列表
红外遥控步进电机
- 红外遥控步进电机C51
红外程序
- 红外遥控的程序例子,可供学习用。、、、、、、、、、、、、、、、、、、、、、、、、、、、、、、、
msp430-IR
- 用msp430 解码 红外遥控器信号,32BIT-An IR signal decoder
nec
- C写的 nec芯片的 红外遥控器的发射 解码程序 51单片机 -C write nec chip infrared remote control launching decoding program 51 MCU
HW
- 红外在单片机上的应用,C语言源码,Keil uVision3工程文件,附原理图及说明学习文档 红外接收电路采用集成红外接收器成品H1,接收器包括红外接收管和信号处理IC,均集成在红外接收器H1内。接收器对外只有3个引脚:Vcc、GND和一个脉冲信号输出PO。Vcc接系统的电源正极(+5V),GND接系统的地线,脉冲信号输出接CPU的中断输入引脚INT0。如果没有红外遥控信号到来,接收器的输出端口PO保持高电平,当接收到红外遥控信号时,接收器件信号转换成脉冲序列加到CPU的中断输入引脚。CPU
MOTOR-LCD1602
- 红外遥控步进电机,可控制电机正传、反转,并且用LCD1602作为显示-Infrared Remote Control stepper motor, can control the motor Story, inversion, and used as a display LCD1602
at89c2051ds1302
- 80C2051与DS1302制作电子钟,采用红外遥控,显示日历及时间。-80C2051 with the creation of an electronic bell DS1302, using the infrared remote control, calendar and time display.
infrared-remote-control-learning
- 基于单片机的学习型红外遥控器C语言源程序。现在很多遥控器都有这个可能,值得参考学习。-MCU-based infrared remote control learning C language source code. Now many have the remote control may be, it is also useful to learn.
ykq
- 万能红外遥控器接收,绝对好用!万能红外遥控器接收,绝对好用!-Universal infrared remote control receiver is absolutely easy to use! Universal infrared remote control receiver is absolutely easy to use!
2
- 红外遥控解码资料,好东西来的,仅供参考-good martieral
yym
- 中文12864LCD显示红外遥控解码,能通过单片机接收红外遥控器发来的信号-Chinese 12864LCD show infrared remote control decoding, through the microcontroller receiving infrared remote control signal sent
IR-51-R
- STC单片机,接受红外遥控器的程序,供参考.-STC microcontroller, receiving infrared remote control program for reference.
hongwai2
- 51单片机控制的红外遥控的接收部分的程序,可实现解调、解码和现实的功能,很实用!-51 MCU controlled by infrared remote control receiver part of the process, can be realized demodulation, decoding and realistic features, very practical!
yyf
- 电视机万能遥控器红外解码程序,适合单片机的红外线发射接收学习。-TV Universal Remote Infrared decoder program
Study_IR_Remote_Control
- 资料包含源码,硬件图,红外相关资料等,本学习型红外遥控器,通过学习一次遥控器的编码,即可脱离原遥控器来遥控电器或者设备,源码很完整,严格测试过,不过由于C52的单片机RAM有限,编码缓冲区长度有限,而不同的遥控器的编码长度也不相同,对于像空调遥控器编码比较长的就会出现学习不了的情况,必须要加外部RAM作为接收缓冲区,或者换用STC的单片机,内部的RAM比较大,不用扩展,用STC还有好处就是不需要外部的eeprom来保存读取的编码,而C52需要用外部的EEPROM来保存编码,这个源码实用的AT24
微型红外追踪及无线遥控车
- 微型红外追踪及无线遥控车 设计-Micro-infrared tracking and wireless remote control car design
基于AT89s52学习型红外遥控器程序
- 此程序可用于89s系列单片机开发板所配备的红外遥控器。
红外接收数码显示程序
- 本程序可以接收红外遥控码,解码并在数码管上显示
红外遥控程序2
- 实现简单无线遥控的程序设计,可以当做课程设计(wuxianyaokongkeyidangzuokechengsheji)
红外学习
- 学习遥控红外信号,任意载波都可学习,会将红外数据存到flash中(Learn infrared remote signal, any carrier can learn)