搜索资源列表
MSP-EXP430F5438(A)-Example-Software
- 铁电开发板上位机加开发板源码MSP-EXP430F5438(A) Example Software-Ferroelectric development board and the development board source MSP-EXP430F5438 (A) Example Software,
FM25L256
- 铁电FM25L256的代码 已经使用没有问题的-Ferroelectric FM25L256 the code has been used without problems
FM25CL6420110112
- 铁电Flash的驱动测试代码,在FM25CL64上测试通过-ferroelectric Flash diver code.Test OK on FM25CL64
tiedian
- 使用stm32的铁电存储器操作函数,铁电存储器写入速度快,无传输等待-The ferroelectric memory using stm32 operating function, ferroelectric memory writes speed, no transfer wait
pic24c02
- 首先pic和铁电24c02通讯,然后从ds18b20中读取当前温度值再把它存取到铁电中的特定位置-First pic and ferroelectric 24C02 Communications, and then from the DS18B20 read the current temperature value and then its access to the ferroelectric in a specific location
CDMAGPRSmodem
- 板上资源: LM2576电源,MAX3232电平转换芯片,11.0592M有源晶振,ATMEGA128L,FM32256(铁电),滑槽式SIM卡座,40PZIF接插件,通信 模块支持CM320,TC35i,MC35i,MC39i,GTM900A/B等模块。 使用方法:1、不焊接M128和FM32256以及晶振,将桥接电阻R29,R30,R31焊上,就是标准串口无线MODEM,根据模块不同可以支持GPRS和CDMA, 当然也可以作为GSM猫或者短信猫来使用。 2、焊上M
F040_i2c
- 本程序是C8051F040的I2C /SMBUS读写程序,实现铁电存储器FM24C04的读写操作。-This procedure is C8051F040 s I2C/SMBUS literacy program, to achieve the FM24C04 ferroelectric memory read and write operations.
lpc2300-I2C
- NXP lpc2300的I2C程序代码,直接采用LPC2300自带的I2C控制器进行操作,包括读写24C02 \读写24C256\读写铁电FM24cl04等-NXP lpc2300 the I2C code, directly using LPC2300 own I2C controller to operate, including reading and writing 24C02 \ literacy 24C256 \ literacy FM24cl04 such as ferroelec
f02024c02
- C8051f020读写铁电24C02 ,随几读写,功能很强大。-C8051f020 read write 24c02
FM24C04test
- c8051f350,如何使用铁电串行存储器FM24C02 KEIL C 汇编多可以-c8051f350使用FM24C02
FM25H20
- 一款铁电存储器的说明文档,FM25H20自己用其感觉还不错!就是有点贵80RMB-A ferroelectric memory documentation, FM25H20 their sense of their own good! 80RMB is a little expensive
dsPIC33_Data_Recorder
- dsPIC33做的数据记录仪,用的MCU是dsPIC33FJ12GP201,数据存储器用的铁电FRAM:FM24CL64-dsPIC33 doing data logger, using the MCU is dsPIC33FJ12GP201, data memory using ferroelectric FRAM: FM24CL64
Ramtron_FM24C64_Driver(NEC_MCU)
- 为电力行业负控终端以及多功能表计使用的铁电技术存储器驱动文件,对应硬件接口为NEC单片机硬件接口资源;对应编译平台为NEC PM-Plus编译仿真环境。-Negative control terminal for the power industry, as well as multi-meter used as a ferroelectric memory technology driver file, the corresponding hardware interface for the
MSP430_IO_for_SPI_to_rerad_FRAM
- 用MSP430通用IO模拟SPI读写铁电存储器-implement SPI With the MSP430 general-purpose I/O port to read and write FRAM
nvram
- 铁电非易失存储器,用于嵌入式dsp外设,掉电前记忆重要数据。-NVRAM
main
- DSP2812铁电存储器操作程序, 24c02电可擦除存储器。-DSP2812EEPROM_programe
msp169
- 使用MSP430设计的流量计代码,有RTC,铁电-MSP430 design flowmeter using the code, there are RTC, ferroelectric
8
- 铁电存储器FM25L256的驱动程序.建议编辑环境:UltraEdit 11.00a+ 制表符宽度为三个字符,程序可读性更好。-FRAM FM25L256 drivers. Recommends editing environment: UltraEdit 11.00a+ tab width of three characters, the program better readable.
SpiReadFM24C64
- 测试铁电FM25CL64的SPI读写驱动程序,采用KEIL51编译程序,速度很快,寿命长,可以替代EEPROM和RAM。-FM25CL64 SPI write code use C51
C_V
- 用来描述铁电存储器MFIS-FET结构的C-V(即电容-电压)关系-Used to describe the ferroelectric memory MFIS-FET structure of CV (ie capacitance- voltage) relationship