搜索资源列表
s3c2440_uboot_dev
- UBOOT for S3C2440 (C) Copyright 2000 - 2002 # Wolfgang Denk, DENX Software Engineering, wd@denx.de. # # See file CREDITS for list of people who contributed to this # project. # # This program is free software you can redistribute it an
MCU_Init
- Freescale MCU 带CAN通讯 MC9S08DZ16 初始化，包刮各端口及总线频率调置。用8MHz晶体谐振器获得16MHz总线频率。-Freescale MCU with CAN communication MC9S08DZ16 initialization, including scraping the port and bus frequency modulation home. 8MHz crystal resonator used to obtain the frequency
u-boot-1.1.1.tar
- 嵌入式bootloader源代码，可以轻松的在一周之内一直到各类MCU上，如MIPS，ARM7，ARM9，XScale，Power PC等平台。-latest version of the embedded Bootloader source code, can easily within a week and have all kinds of MCU, such as MIPS, ARM7, ARM9, XScale, Power PC platform.-uboot1.1.1
CAN
- 意法公司的STM32芯片的CAN总线程序-STMicroelectronics STM32 chip' s CAN bus procedures
can
- CAN communicator based on TI F2407
CAN
- TMS320LS2407的程序 CAN总线实验-CAN bus TMS320LS2407 experimental procedures
AVRmenu
- Another AVR-gcc example menu for LCD 2x16 display. It can be simulated in VMLab.
troublecode
- 读取汽车OBD-II系统存储在ECU中的故障码，连接扫描仪就可以使用。-Read automotive OBD-II system is stored in the ECU Fault codes can be used to connect the scanner.
CAN.BUS.for.DSP.2407
- DSP 2407的CAN总线初始化配置，采用CAN OPEN协议-The configuration of the CAN-bus register for the DSP 2407 with the CAN-OPEN protocol
CAN
- XSBase270实验开发平台CAN总线实验源码-XSBase270 experimental development platform for CAN-bus test source
canctl
- Can 通信程序，非常标准的通过can协议完成的主机与板卡之间的一种通信程序。-Thecan communication procedures, very standard through agreement with the host Can finish a communication between card program.
lpc2368_can
- LPC2368(2368)的CAN 总线驱动的示例程序-LPC2368 (2368) the can bus driver sample programs
8051ApplicationCode
- 该程序为基于51单片机的接口和片外应用的代码，在设计51单片机时可供参考，代码包括RS232通信、I2C、SPI、单总线、CAN总线、键盘、LED、LCD、AD/DA等应用。各工程在Keil调试通过，喜欢的朋友可供参考。-The program is based on the 51-chip microcontroller interface and application code, in the design of microcontroller 51 when the reference
can
- 这是一个CAN总线通信的节点程序，是我自己编写的，希望指正。-This is a CAN bus communication nodes procedures, the preparation of my own, and I hope correct me.
CANBUSANALYZER
- A can BUS Analyzer, you can check the data on a CAN BUS
CAN
- CAN demo code,demo source code for CAN module -demo source code for CAN module
dsp2812_CAN
- 刚调通的2812CAN总线通讯，设置波特率为250kps，为标准CAN的发送模式-Just tune tung 2812CAN bus communication, set the baud rate of 250kps, a standard CAN-send mode
can
- 在ARM7开发板下实现CAN总线驱动的开发，已调试成功，修改工程路径即可用，CAN控制芯片为MCP2510-the drivers of canbus in the arm7
can
- 详细分析了CAN驱动源码，中文注释，附SJA1000电路连接图-analysis the source code of can bus driver， and do comment in Chinese，the circuit of SJA1000 is added，too！
can-flash
- 三菱16位单片机M306N0系列，通过CAN BUS烧写FLASH。-Mitsubishi 16-bit microcontroller M306N0 family, through the CAN BUS Shaoxie FLASH.