搜索资源列表
ZStack-CC2530-2.3.0-1.4.0
- 基于Zigbee网络的 MQ_2传感器信号采集与报警-Based on the Zigbee network MQ_2 sensor signal acquisition and report to the police
PWM
- CC2530定时器产生pwm信号调整LED亮度-CC2530 timer to generate pwm signal to adjust LED brightness
Test
- 源码已经调试好的，cc2530控制步进电机正反转程序-Source code debugging has been good, cc2530 program controlled stepper motor reversing
RFID
- 基于cc2530的RFID射频卡程序，已经调试好的-The RFID-based cc2530 RF card program has been debugged
adc_voltage
- 基于cc2530单片机的用片内的adc做电压表的源码-Do voltmeter adc cc2530 source-based microcontroller with on-chip
Watch-Dog
- zigbee芯片cc2530的看门狗，采用IAR平台调试 。-cc2530 watchdog, using the IAR debugging platform.
transmission-quality-
- 基于zigbee的cc2530无线传输质量的检测及0.96寸oled的显示-Based on the cc2530 zigbee wireless transmission quality detection and 0.96 inch oled display
BH1750FVI_cc2530
- BH1750FVI 代码，可以在裸机上和协议栈上运行，本人项目用的，测试过-BH1750FVI for CC2530, I have tested on Zstack .
BH1750
- IAR ZStack 开发，基于I2C 的光照强度模块，BH1750FVI， 可以在协议栈上运行-bh1750 cc2530
MMA7455
- 利用CC2530实现IIC总线通信协议采集三轴传感器MMA7455数据，读取MMA7455的数据，并通过口串口在上位机显示 -Use CC2530 implement IIC bus communication protocol data acquisition triaxial sensor MMA7455, MMA7455 read data through the serial port on the PC display
air
- 实现ZigbeeCC2530中空气温湿度的采集-Implement Zigbee CC2530 hollow temperature and humidity acquisition
CC2530watchdog
- CC2530看门狗测试, 首先进行看门狗的初始化，然后进行喂狗防止程序跑飞！-The CC2530 test of watchdog.
CC2530LCD12864
- 听过CC2530和LCD12864来显示字符串！首先定义字模库和各个函数，然后初始化，写字符串！-The test of LCD12864 in CC2530.
CC2530Timer3Interrupt
- CC2530的定时器3中断方式测试！首先初始化Timer3，然后定时，当定时时间到，产生中断，通过LED灯取反显示！-The test of Timer-3 in interrupt solution in CC3530.
CC3530LedUART0
- 通过串口0向CC2530发送字符串，如果字符串达到数量或以#结束，则将所有接受到的返回，并通过LED灯翻转显示！-The test of UART0 in cc2530!
timer
- IAR工程源码,关于CC2530定时器的使用-source code for IAR
1.IO-control-Led-on-or-off
- 本代码是关于CC2530的源码，讲的是如何用IO控制LED灯的亮灭-The source code is on the CC2530, talking about how bright IO control LED lights off
3.key-control-LED
- 本实验是关于CC2530的源码，讲的是如何用按键控制LED灯的亮与灭-This experiment is about the CC2530 source tells of how keys to control LED lights on and off light
9.use-uart-to-send-string
- 本源码是关于CC2530的串口，通过串口发送字符串-The source is about the CC2530 serial port, serial port by sending a string
8.timer3-interrupt
- 本源码是关于CC2530的定时器3，讲解了定时器3的中断用法-The source is about the CC2530 timer 3, timer interrupt to explain the usage of 3