搜索资源列表
工程
- 基于cc2530智能高校防防火防盗 上位机界面设计 使用Tkinter插件 serial插件 多线程(Based on CC2530 intelligent University fire prevention and anti-theft host computer interface design, using Tkinter plug-in, serial plug-in, multi-threaded)
7.DHT11终端节点+休眠
- 读取DHT11值，休眠，回传给终端节点。(Reads the DHT11 value, hibernate, and returns to the terminal node.)
DS18B20测温并在OLED屏幕显示
- 在oled上显示温度,温度传感器可以感受外界温度变化，自己看吧，程序员不会说话(zai oled shang show termperature)
从零开始学习Zstack
- 学习zstack的好帮手，太好了，从零开始，你再也不用担心自己是个傻X了(you can you up ,who know who nb)
install.res.1033
- Read this RoadTest review of the 'Anaren AIR CC2530 Booster
13物联网2陈维2013313228
- cc2530驱动12864lcd，无需字库，实现软件驱动，简单方便快捷(CC2530 driver 12864lcdcc2530 drive 12864LCD, without font, software drivers, simple, convenient and fast)
串口透传
- 串口透传，pc端输入任意数经过终端可以通过组网在协调器显示(The serial port passes through, the PC end inputs any number, through the terminal, may through the network display in the coordinator)
1.协议栈工作流程和无线收发控制LED
- 协调器和终端组网成功后LED闪烁。说明组网成功(LED blinks after coordinator and terminal networking successfully)
基本功能版本
- 利用CC2530实现温湿度，光强，电压等信息的采集以及串口显示(Using CC2530 to achieve temperature and humidity, light intensity, voltage and other information collection, and serial display to the PC.)
实验2 点对点通信
- 两个ZigBee节点进行点对点通信，ZigBee节点2（终端节点EndDevice，稍后，下载EndDeviceEB里的代码）发送“LED”三个字符，ZigBee节点1（协调器节点Coordinator，稍后，下载CoordinatorEB里的代码）接受数据后，判断接受到的数据是否为“LED”，是，则使板子上的LED灯闪烁。(Two ZigBee node point-to-point communication, ZigBee node 2 (terminal node EndDevice,
实验4 串口
- PC端串口调试助手向板子发送数据，板子接受到数据后，再把数据发送回给PC端串口调试助手(PC port serial debugging assistant to send data to the board, the board accepted the data, and then send the data back to the PC side, serial debugging assistant)
实验5 无线温湿度检测试验
- 协调器建立ZigBee无线网络，终端节点自动加入网络，然后终端节点周期性地采集温度并将数据发送到协调器.协调器接受数据并通过串口把接受到的数据传给PC端的串口调试助手。(The coordinator in a ZigBee wireless network, terminal nodes automatically join the network, then the terminal node periodically collects temperature and send the da
实验6 NV操作实验
- 通过串口调试助手发送“nvread”命令，开发板接受到该命令读取NV存储器中的数据并发送给PC端的串口调试助手。(Through the serial debugging assistant to send "nvread" command, the development board to accept the command to read the data in the NV memory, and sent to the PC side of the serial d
08_RF
- CC2530裸机操作射频寄存器进行点对点、一点对多点的通信(CC2530 bare metal point to point communication)
W5500_DHCP
- cc2530+W5500自动获取IP地址（dhcp）(The automatic acquisition of IP cc2530+W5500 (DHCP).)
1 PWM高级定时器互补输出
- STM32高级定时器实现互补输出通过RC震荡电路输出正弦交流电，实现直流转交流。两个通道之间存在一个死去时间。(The STM32 advanced timer implements complementary output through the RC oscillating circuit to output sinusoidal alternating current to achieve direct flow communication)
rxtxserial
- 可以查看尺寸22530源码，当然啦其中包含了好多的串口的功能即实现的技术和相关代码(You can see size 22530 source code, of course, which contains a lot of serial function, that is, the implementation of the technology and related code)
读写EEPROM 模拟IIC
- IIC协议 EEPROM24c02 存数读取数据,用于检测EEPROM性能，测试方法如下：写入24c02一个数据，然后在内存中改变这些数据，掉电后主内存将失去这些信息，然后从24c02中调入这些数据。看是否与写入的相同。(IIC protocol EEPROM24c02 number read data, is used to detect EEPROM performance testing methods are as follows: write a 24C02 data, and the
ZStack-CC2530-2.5.1a
- 完整的协议栈demo程序，包括终端节点，协调器节点以及路由节点(Complete protocol stack demo program, including terminal nodes, coordinator nodes and routing nodes)
ADC做电压表
- 将CC2530的ADC驱动后用作电压表，实时测得电压(After the CC2530 of ADC is driven, it is used as voltmeter, and the voltage is measured in real time)