搜索资源列表
msp430serialcode
- msp430模拟串口的源程序 有原理解释-Serial Controller simulation is the principle source explained
MSP430adcuart
- MSP430定时器触发ADC并送串口的程序，不同于官方网站，适用于F14X,F16X系列-MSP430 timer trigger serial ADC and sent to the procedures different from the official website applies to F14X, F16X Series
KEYUART
- MSP430的P2口接4*4按键，在PC短运行串口调试软件，可显示键号-MSP430 P2 I received 4 * 4 keys, in the short run PC serial debugging software can show that the key issue
KEYUARTINTERRUPT
- MSP430的P2口接4*4键盘，通过中断方式实现串口通讯，通过PC端运行串口调试软件显示键号-MSP430 P2 I received 4 * 4 keyboard, interrupted achieved through serial communications, PC terminal operations through serial debugging software, and display key,
testNode
- 该工程是由IAR Embedded Workbench开发，完成的功能是由DS1820采集温度数据，通过单总线方式发送到MSP430中，再由处理器通过串口通信将数据发送到PC机中进行记录．-the project by the IAR Embedded Workbench development, The function is to be completed by the DS1820 temperature data collected through the single bus disp
UART_Send
- 基于msp430的软件模拟串口发送程序（在MSP430F147型单片机上成功实现）-Controller Based on the simulation software Serial this procedure (MSP430F147 MCU - successful realization)
UART_Recv
- 基于msp430的软件模拟串口接收程序（在MSP430F147型单片机上成功实现）-Controller Based on the simulation software serial receiver (the MSP430F147 MCU - successful realization)
fet440_uart01_09600
- MSP430系列单片机 UART串口通信程序-MSP430 MCU UART serial communication program
流量计
- 以MSP430单片机为主控芯片，由TM1727液晶驱动芯片驱动段式LCD液晶显示屏，在段式LCD液晶显示屏上显示累计流量、温度、压力、瞬时流量、电池电量、流量计工作符号、天线信号强度，通过串口向差压采集电路读取温度值、瞬时流量，采用Modbus通信协议由无线通信模块将数据上传。(With MSP430 chip by TM1727 LCD driver chip driver LCD LCD display, display the cumulative flow, temperature, p
2553模块化程序以及模板
- 430 2553 模板程序例程，串口，定时器，液晶，按键，PWM，ADC等(430 2553 template program)
msp430afe_uart_115k
- MSP430AFE253 115k波特率串口程序(MSP430AFE253 115K baud rate serial program)
UART2LCD
- MSP430G2553开发板驱动串口和5110液晶屏显示的代码。使用IAR打开。(The MSP430G2553 development board drives the serial port and the 5110 LCD screen to display the code. Open with IAR.)
Lab 6 UART_RS232
- 基于MSP430f5529的串口程序，能在墨水版上输出(We will use USCI_Ax module with UART mode, Timer_A module, and TFT display. 1. Configure UART mode 2. Initialize E-ink screen (TFT) display 3. Configure Timer_A for interrupt Transmit one character through UART every o
09-红外收发器
- PC上运行串口大师等串口调试软件，通过USB接口向开发板发送数据, 开发板收到数据帧后，将其由红外端口发送；如开发板接收到红外信号，当红外端口接收到完整数据帧后，开发板将数据由USB口送至PC。本程序未采用NEC或Philips的红外协议，旨在展示一种像使用串口一样 使用红外接口的方式，实验表明，这一方法十分有效，在1200bps、3米 距离的条件下仍有非常好的收发效果。(PC run serial master serial debugging software to se
07-USB通讯
- 主程序检测有按键按下则通过USB端口发送"This is BW-DK5483" , 可将开发板USB接口与PC连接，PC上运行串口大师等串口调试软件， 打开USB串口接收并观察开发板发送数据，也可由PC端发送数据至开发板,开发板将接收数据发回PC(The main program detects a button press through the USB port to send "This is BW-DK5483", the USB develop
RF905-MCU-PC
- MSP430通过串口实现与上位机的通信。(MSP430 communication with the host computer through serial port)
Lab07-1 RS232
- TI公司的MSP430例程 RS232串口通信实验(TI's MSP430 routine RS232 serial communication experiment)
多点温度测量
- TI msp430温度测量的原文件 可以多点测量温度 串口通信(The original document of TI MSP430 temperature measurement)
MSP430F449例程
- 实现了时钟、定时器、AD、显示屏显示、串口通信等功能(The functions of clock, timer, AD, display and serial port communication are realized.)
msp430底层驱动代码
- 里面包含adc，dma，lpm，gpio，ucs，spi，串口，iic，wdt等一系列F55xx的底层驱动代码。供广大网友使用