搜索资源列表
STM32F103
- STM32F103的一个DEMO软件，对于初学者可以看看。-STM32F103 a DEMO software, for beginners can see.
STM32F103-V3.5
- 1，本文件夹包含53个标准例程，所有例程均在战舰V3 STM32F103开发板上测试通过。 2，本文件夹下所有用到LCD的例程，都支持ALIENTEK 2.4/2.8/3.5/4.3/7寸电阻/电容触摸屏。 3，本文件夹下的所有例程，都是采用MDK5.14编译器。 4，编译生成的.hex文件（可以用来下载到开发板的）都存放在工程/OBJ文件夹里面。 -1, 53 standard routines, this folder contains all the routines
STM32F103-control-6-steering-gear-
- STM32F103ZET6同时控制6个舵机的程序，还可以调节6个舵机的运行速度。-STM32F103ZET6 simultaneously control 6 steering gear program, you can also adjust the speed of the 6 steering gear.
STM32CAN
- STM32F103 Can两块板子收发程序-STM32F103 Can two boards transceiver procedures
stm32f103---Entrance-guard-card
- stm32门禁卡工程，外接硬件后可直接下载到stm32板子上，刷卡识别通过-STM32 access card project, the external hardware can be downloaded directly to the STM32 board, credit card identification through
EKBoard
- stm32f103开发板资料，以前使用的，可以测试通过(STM32F103 development board information, previously used, you can test through)
IIC
- IO 模拟I2C程序，可以自适应从机150KHZ以下频率(IO simulation I2C program, you can adapt to the following frequency from the machine 150KHZ)
MB001U
- 基于STM32F103 IMU开发，CAN通信(Based on STM32F103 IMU development, CAN Communications)
实验一输出方波flash版
- 实现方波输出小功能，给位可以看看，功能简单易懂(Realize square wave output small function, give bit can see, the function is simple and easy to understand)
STM32F013ZET6测试程序
- 次程序为单片机的测试DEMO，可以下载下来一起学习！(The program is a single chip microcomputer test DEMO, which can be downloaded and studied together!)
PC机 采用主从方式 采集总线上的多块MINI板
- 主从方式，主机通过CAN读取从机的单片机温度数据，主机收到的数据在PC端串口助手显示。 单片机stm32f103c8t6(Master/Slave Master read temper data from Slave through Can-bus. The temperature data Master received will print to PC through UART&USB transmitter. MCU is stm32f103c8t6.)
TFT
- TFT彩屏驱动程序的一部分说明，并且显示正弦波，并能调整位置(That part of the TFT color display driver, and display the sine wave, and can adjust the position.)
DHT11STM103
- STM32F103能实现温湿度的检测的代码，工程文件直接打开就可以用(Temperature and humidity detection can be achieved)
DIANJI
- 可实现二相四线直流步进电机的正反转，控制转速，转动角度，搭配精密丝杠工作台使用，可实现精密工作台精确移动，脉冲当量可达到0.01mm/rad，配有LCD5110液晶显示程序，4*4键盘控制程序，可实现人机交互，按键调节参数，实现电机控制。(The second phase four wire DC stepper motor reversing, speed control, rotation angle, collocation precision screw bench, can reali
基于stm32f103rc的USB_HID模拟键盘并发送卡号成功
- 1、基于stm23f103c8t6的开发板开发，外接rc522读卡板。 2，实现让windows系统把设备认成hid键盘，当刷M1卡时，把4字节的卡号以键盘输入的形式上送到电脑。 3，已在xp，win7系统上测试。把鼠标放在文本输入框中，刷卡，卡号即可显示在文本框中，并回车换行。(1, based on the stm23f103c8t6 development board development, external rc522 read card board. 2, to achieve
frequency（PA0）
- 频率计的基本原理是用一个频率稳定度高的频率源作为基准时钟，对比测量其他信号的频率。通常情况下计算每秒内待测信号的脉冲个数，此时我们称闸门时间为1秒。闸门时间也可以大于或小于一秒。闸门时间越长，得到的频率值就越准确，但闸门时间越长则没测一次频率的间隔就越长。闸门时间越短，测的频率值刷新就越快，但测得的频率精度就受影响。本文数字频率计是用数字显示被测信号频率的仪器，被测信号可以是正弦波，方波或其它周期性变化的信号。如配以适当的传感器，可以对多种物理量进行测试，比如机械振动的频率，转速，声音的频率以及
stsw-stm32014
- adc采样多种模式应用实例，包括多通道、单通道、独立、定时器触发模式等等。(The regular channel converted by ADC2 is channel14 (the potentimeter). The converted values of channel12 and channel14 are stored in ADC_DualConvertedValueTab[] table as 32bit format, and are separated and stror
计数器外部测速
- PA0口输入捕获可以测量低频信号 3000hz(PA0 port input acquisition can measure low frequency signals)
HJduino
- 核心板为stm32f103，该小车红外遥控代码是在keil 5 环境下用c语言编写的程序。实验多次，稳定性好，并且有相应注释，可灵活更改相关数据。(Core board for STM32F103, the car infrared remote control code is in the Keil 5 environment, written in C language program. Experiments many times, good stability, and correspo
STM32ATK-7' TFTLCD电容触摸屏显示
- STM32F103处理器显示电容触摸屏的驱动，可以参考这种C语言例程写法(STM32F103 processor display capacitive touch screen driver, you can refer to this C language routines written)