搜索资源列表
-
1下载:
1.找点一段心电信号,画出信号时域波形和频谱图;
2. 利用MATLAB中的随机函数产生噪声加入到心电信号中,使心电信号被污染,读出污染后的号并画出对应信号的时域波形和频谱图;
3.用双线性变换法设计一个Butterworth带通滤波器,输出所设计的滤波器的阶次,分子、分母多项式的系数,画出滤波器的频率响应(幅频响应和相频响应)曲线;(也可以根据自己需要设置滤波器性能指标)
带通通滤波器设计性能指标:fs1=10Hz, fp1=20Hz, fp1=1000Hz, fs2=120
-
-
2下载:
用于心电信号滤波的LMS自适应噪声对消器设计,胎儿信号包含母亲信号噪声,采用自适应算法将母亲信号对消掉,得到胎儿心电信号。-ECG filtering for LMS adaptive noise cancellation design, the fetus signals the mother signal contains noise, the use of adaptive algorithm will signal to eliminate the mother, the fetal E
-
-
1下载:
-
-
0下载:
A few examples of designing and implementing fir filters with Matlab-filtering a signal taken from the mic input of the soundcard and putting it on the headphones output chanel and removing noise from ECG.I m uploading this file just because I need t
-
-
1下载:
1. 用双线性变换法设计一个巴特沃斯低通IIR数字滤波器。设计指标参数为:在通带内频率低于0.2π时,最大衰减小于1dB;在阻带内[0.3π, π]频率区间上,最小衰减大于15dB.
2.0.02π为采样间隔,打印出数字滤波器在频率区间[0, π/2]上的频率响应特性曲线。
3. 用所设计的滤波器对实际心电图信号采样序列进行仿真滤波处理,观察总结滤波作用与效果
附:心电图采样序列x(n)
人体心电图信号在测量过程中往往受到工业高频干扰,所以必须经过低通滤波处理后,才能作为判断心脏
-
-
0下载:
本次实验是要我们先产生心电信号,再加噪声再滤波。由一个心电信号数据表输出心电信号,由于已知的心电信号有噪声,所以我先将信号进行滤波,得到正确的心电信号。再加噪声,通过滤波可以得到高频和中频噪声,将原信号加上噪声显示再滤波。每次的时域信号都画出了他们相应的频谱,便于观察。每次的滤波我也尝试了不同的滤波器。-This experiment is to produce our first ECG, together with noise and then filtering. ECG data fro
-
-
1下载:
采用小波变换的方法实现心电信号的滤波,分别使用了硬阈值、软阈值和改进阈值方法,并实现了滤波效果的评价(均方差和信噪比)-Wavelet transform of ECG signal filtering method, respectively, using a hard threshold and soft threshold and improve the threshold method, and to achieve the filtering effect of the evaluat
-
-
0下载:
Several signed LMS based adaptive filters, which are computationally
superior having multiplier free weight update loops are proposed for noise
cancellation in the ECG signal. The adaptive filters
-