搜索资源列表
danpianjishiyandagang
- 熟悉keil仿真软件、proteus仿真软件的使用。了解并熟悉单片机I/O口和LED灯的电路结构，学会构建简单的流水灯电路。掌握C51中单片机I/O口的编程方法和使用I/O口进行输入输出的注意事项。-Familiar with the keil simulation software, proteus simulation software use. MCU I/O port and the circuit structure of the LED lights, and become fami
MCU-UART-keil-src_Protues.RAR
- 单片机双机串口通信含keil源程序_使用Protues仿真-Single-chip dual-serial communication with the keil source _ use Protues Simulation
Keil-uVision2
- kill的使用及与单片机之间的程序仿真，希望对大家有用-use of kill and simulation, with the program between the microcontroller and the hope that useful
ds1302+液晶仿真
- 使用proteus与KEIL之间进行软件仿真，用ds1302+液晶LM1602仿真出一个定时器。
jipinqi
- 51液晶显示转速的代码，用的是keil仿真，数值是波形频率的60分之一-51 LCD speed code, keil simulation, numerical waveform frequency 60
dianyazhuanhuan
- 把0~5v的电压值转换到0~100度的温度，并用51液晶显示，采用keil仿真-0 ~ 5v voltage value is converted to a temperature of from 0 to 100 degrees, and with 51 of liquid crystal display, using keil simulation
qdq
- 八位LED点阵显示数字抢答器 PROTEL仿真文件 KEIL仿真文件-Eight LED dot matrix display digital Responder Protel simulation files KEIL simulation files
DAC1210
- 使用Proteus+Keil仿真环境，设计完成了DAC1210的锯齿波信号发生器。-Base on Proteus & Keil simulation environment , designed the DAC1210 sawtooth signal generator .
alarm
- 利用proteus和keil仿真报警系统，编程语言为c-Use proteus and keil simulation alarm systems, programming languages c++
motor
- 采用80C51+ULN2003A,实现正反转可控的步进电机，proteus+keil仿真，C语言编程。-Using 80C51+ULN2003A, achieve positive controllable stepper motor, proteus+keil simulation, C language programming.
alarm-
- 利用ADC0808实现调温报警器的功能~。内部包含PROTEUS keil仿真图 源程序等-Achieved using the ADC0808 thermostat alarm function ~. Interior contains PROTEUS keil simulation diagram source code, etc.
DS18B20-protues-keil-c
- 利用protues仿真，把DS18B20温度传感器测到的数值显示在2位数码管上-Use protues simulation, the DS18B20 temperature sensor measured values are displayed in the two digital tube
Proteu-case-with-keil
- Proteu与keil案例,采用C语言进行仿真-Proteu case with keil
keil-uVision2
- Keil uVision2 应用 包括实际实验版仿真-Keil uVision2
keil
- 使用AT89C52用protues下仿真出12864显示DS18B20的代码-Under protues simulation using AT89C52 with the code 12864 DS18B20
Keil-uVision4PJlink_v1.0
- 介绍了关于使用仿真器jlink和mdk仿真程序时的一些工程设置，还是比较实用的-Describes some of the projects set up on the use of simulators jlink and mdk simulation program, it is quite useful
8051_UART_T1--V1.0.0.2
- 8051单片机串口数据包收发程序，中断方式收发，节约了CPU的资源。本代码是由微控制器硬件及驱动网的代码生成器生成的，在线可以设置晶振频率，波特率，是否使用中断函数等设置及裁剪功能，这个工程本身是晶振11.0592MHz,波特率9600的情况。这里给个链接吧http://www.hdmcu.com/codegenerator_html/webcg-23.html Keil仿真测试通过。 适用于：8051 89C2051 89C51 89C52 89C55等单片机的串口。-8051 uar
Keil-2
- 基于单片机的水塔自动监控水位设计与仿真。-Automatic monitoring of the water level design and simulation of microcontroller-based towers.
Kei-S3c2440
- keil仿真s3c2440,使用keil源码级调试教程，很好的资料。-keil simulation s3c2440, source-level debugging using keil tutorial, very good information.
LTC1655-keil-c
- 16bit DAC仿真, has been verificatied and validatied in pretous softare-16 bit DAC simulation code， has been verificatied and validatied in pretous softare