搜索资源列表
QQ2008
- LED的控制和使用,这里主要介绍的是LPC2106的控制程序和应用。-LED control and use of, this is mainly being introduced is the LPC2106' s control procedures and applications.
lpc21xxboot
- lpc2104/lpc2105/lpc2106的特殊寄存器及固件程序,启动程序-lpc2104/lpc2105/lpc2106 special registers and firmware to start the program
LPC210624C02I2C
- LPC2106+24C02 I2C的仿真, 是在proteus上仿真-LPC2106+24C02 I2C
LED
- LPC2106的裸机程序控制LED数码管显示0-F字符,同时控制4个LED显示对应的十六进制。-LPC2106 bare metal process control LED digital display 0-F characters, simultaneous control of four LED display the corresponding hexadecimal.
FIQ
- LPC2106的裸机程序,控制FIQ中断。-LPC2106 bare metal process control FIQ interrupt.
PWM
- LPC2106的PWM控制程序,一个采用PWM控制蜂鸣器0.5S响一次,一个为PWM的双边沿控制程序。-LPC2106 the PWM control procedures, a PWM control with a buzzer 0.5S ring, one for the double edge PWM control procedures.
RTC
- LPC2106的RTC模块程序,分别为RTC控制蜂鸣器1s响一次,led灯1s亮一次,RTC唤醒掉电的CPU,控制数码管显示和万历年。-LPC2106 the RTC module procedures were 1s RTC control ring a buzzer, led a bright light 1s, RTC wake-up power-down the CPU, control the digital display and 10 000 years.
WatchDog
- LPC2106的看门狗程序,唤醒掉电CPU。-LPC2106 watchdog program, wake up power-down CPU.
LPC-P2106-button_led
- An example of the LPC2106 development board that lights the leds on button press!
KType_Thermal_sensor_LPC2106
- 基于LPC2106单片机做的K型热电偶仿真,有源代码和Proteus的电路图。 编译好的代码直接放进Proteus直接运行,连板子也省了-Based LPC2106 microcontroller to do K-thermocouple simulation, source code, and Proteus schematic. Compiled code directly into the Proteus run directly, with the board but also save
Makefile
- Makefile for LPC2106
KS0108_LPC2106
- 基于LPC2106的12864液晶驱动(控制芯片KS0108),在PROTUES下测试成功。-an example for 12864_lcd driver base on lpc2106,test succeed under PROTUES.
WDT
- lpc2106的看门狗仿真程序。使用ADS编辑的。-lpc2106 watchdog simulation program. Edited using the ADS.
RTC
- LPC2106的RTC仿真程序,使用ads编辑的。-The RTC LPC2106 emulator, use the ads to edit.
TIMERLED
- LPC2106的定时器仿真程序,使用ads编辑的。-LPC2106 timer simulation program, using the ads to edit.
UART0
- LPC2106的串口仿真程序,使用ads编辑的。-LPC2106 emulator serial port, use the ads to edit.
UART0_FIFO
- LPC2106的串口的FIFO仿真程序,使用ads编辑的。-LPC2106 emulator serial port of the FIFO, using ads to edit.
EINT1
- LPC2106的外部中断仿真程序,使用ads编辑的。-LPC2106 external interrupt simulation program, using the ads to edit.
LPC2106bootloader-interrupt
- 基于PROTUS的LPC2106仿真,一个简单的BOOTLOADER-Simulation-based PROTUS the LPC2106, a simple BOOTLOADER
fft
- LPC2106控制的对信号进行FFT分析的程序-LPC2106 controlled by the signal FFT analysis of the program