搜索资源列表
Flow_Led
- 流水灯的设计，使8个LED灯 循环点亮。移动方式可以在模块里面修改-Water lamp design, lit 8 LED lights cycle. Moves inside the module can be modified
SpiCommMast
- SPI串口通讯程序，主机发送数据后，LED灯点亮。-SPI serial communication program, the host sends data, LED lights lit.
ax12
- 基于IPC-Beck DB50开发平台（SC-13)使用RTOS提供的API编写的智能马达AX-12的简单通信程序 功能：点亮AX-12指示LED灯 -IPC-Beck DB50-based development platform (SC-13) prepared using the RTOS API provides intelligent motor AX-12 features a simple communications program: AX-12 light LED li
EMBEST_LED
- LED测试程序 点亮和关闭LED 只做了2个LED的控制-LED light on and off LED test program only had two LED control
TimeOut_C
- 定时器与中断，每一秒残生一个中断，点亮8个led灯-Timer interrupt, an interrupt every second remaining years, 8 led lamp light
TIME0
- 利用TIME0控制与P0口相连的8个LED指示灯依次上移点亮-P0 port using TIME0 control and connected to 8 LED lights were lit on the Move
jiaotongdeng
- 单片机实现的交通灯程序1:利用单片机的定时器产生秒信号，控制十字路口的红绿黄灯交替点亮和熄灭， 2:能够用4只LED数码管显示十字路口两个方向的剩余时间。要求能用按键设置两个方向的通行时间-MCU traffic light program 1: Using the MCU timer to generate the second signal to control the crossroads of red, green and yellow alternately turning on
right-lateral--running
- 右移运算流水点亮P1口8位LED，新手值得一看的入门小程序.-The right lateral operation running water lightens P1 mouth 8 LED
lsd
- 按键控制LED流水灯；按键1按下前8个灯从左到右依次点亮，按键2按下中间前8个灯从左到右依次点亮，按键3按下所有灯全亮-Water control button LED lights sequentially lit buttons the eight lights left to right 1 Press button 2 press from left to right is lit in the middle eight lights, key 3 Press All full bri
LEDliudong
- 跑马灯，让八个led灯循环的点亮，里面主要是使用了分频加计数-through water
C51
- keil 51 的红外收发代码，简单，测试可行，当接收到红外信号，指定的led 灯会点亮。-keil 51 infrared transceiver codesimple test feasible, when the infrared signal is received, the specified LED lantern is lit.
8led
- 51单片机开发板上8个led按顺序来回依次点亮-51 MCU development board 8 led back and forth in order to light up sequentially
exp
- IAR 8051 LED点亮源码 每一秒状态改变一次-Change once every second state of the the IAR 8051 LED lights up source
KEY
- 按键扫描程序 * * 开始点亮P1LED * * 按P34 LED向右移一位 * * 按P35 LED向左移一位-Key shift
LED_4key
- /****************************************************** 程序功能：用中断方式读取四个独立式按键的键值，同时用 D1~D4四个LED的点亮来指示k1~K4四个按键的按下 ---------------------------------------------------- 测试说明：按动K1~k4四个按键，观察LED是否正确点亮 *********************************************
74HC595_single_led
- 实现74HC595控制24个led。依次点亮，和同时点亮-74HC595 control 24 LEDs. Were lit, and lit at the same time
12
- 彩灯是由发光二极管（LED）构成的8×8点阵。当行、列有效时，其交叉点的LED被点亮，当多个LED被点亮时即可形成一定的图案或字符。 彩灯控制器结构框图 改变点亮方式将产生不同的效果。举例8×8矩阵板显示“中”字图样以及对应的行译码器输出和和列存储器存储代码表。-failed to translate
liushuideng
- 流水灯用Do-While语句控制P0口LED灯 用if语句控制P0口8位LED的点亮等-Water lamp with Do-While statement controls P0 port LED lights controlled with an if statement P0 port 8 LED lighting, etc.
ledtest
- 用单片机控制LED发亮程序，当单片机输出一个信号，对应控制LED点亮-TEST LED
work_2
- 1、将51单片机片内数据存储器30H单元～3FH单元的数据清零，如果成功，点亮EZ-51开发板上的某个LED。 2、将51单片机片内数据存储器30H单元～3FH单元的内容复制到50H单元～5FH单元，如果成功，点亮EZ-51开发板上的某个LED。 3、将51单片机外部数据存储器1000H单元至1FFFH单元数据清零。该任务无法通过EZ-51开发板验证，可以通过Keil C的仿真调试验证。 4、将51单片机外部数据存储器1000H单元至1100H单元的数据复制到2000H单元至2100