搜索资源列表
Hw_code
- 红外发射接收程序 1.圈数测量:红外一体化接收头，通过外部中断引脚,1个信号加1 2.单位时间:定时器0,提供1s的时间信息 3.显示单元:8位共阴数码管,P0控制数码,P2控制位码 4.根据频率，控制状态-infrared transmitter-receiver 1. Circle Measure : integrated infrared receiver first, through external interrupt pins, a signal plus 1
hongwai
- 上传一份关于红外通信 常用的红外发射和接收头的引脚判断
main
- 利用红外发射器和接收器，可是小车按照设定好的黑线寻迹-The use of infrared transmitter and receiver, but the car set in accordance with good black line tracing
fuzahongwai
- 一个复杂的红外控制小灯程序，将红外发射和接收分开来写的程序，独立成两个模块-Infrared control of a complex process of small lights, to transmit and receive infrared separate written procedures, separate the two modules
count
- 智能汽车测速用码表，精切到百分秒，检测电路简单，只需一对红外发射接收管和lcd1602便可。-Intelligent Vehicle Speed code table used, the percentage of precision-cut second detection circuit is simple, just a pair of infrared emission will be able to receive control and lcd1602.
hongwaifashejieshou
- 红外发射接收 利用单片机控制红外发射管发射脉冲个数 红外接收根据接收的个数来确定相应的指令-hognwai
ft
- 机顶盒源代码与红外编码资料 红外发射程序：红外通讯使用的格式为字节直接发送模式，提供4位自校验的函数 * * 通讯时记录载波宽度。未使用串口帧格式。软件载波。-Set-top box source code with the infrared emission infrared data encoding process: the use of infrared communication format for bytes sent directly to provide four s
1234(2)
- 接收译码电路由红外接收放大器、音频译码电路和声控执行电路组成。接收红外二极管应采用与红外发射管配对的管，在收到红外光脉冲后，接收管D1的两极间电阻作与频率相应的变化，由光信号转化为电信号，经VT1和IC1放大-Received by the infrared receiver decoding circuit amplifier, the audio decoding circuit and voice-activated circuit implementation. Should be us
Car
- 利用红外发射器和接收器 使小车能够沿着地面上的黑线循迹前进-Car that can follow the black lines using the sensors
bjdj
- 采用单片机AVR mega16作为控制系统的核心，以4*4的小键盘为输入设备，以反射式红外发射-接收器为数据采集部件，用L298N芯片组成功率放大电路驱动电机，四连排数码管作为显示电路的部件，利用直流稳压电源供电，用数码管显示电机的转速，完成对电机的转速、转向、启停等多种工作状态进行快速而准确的控制，组成了一个比较完整电机控制及转速显示闭环系统。-This design uses a singlechip AVR mega16 to be the core device of the contr
USB_IR_MFC
- MFC写的USB红外驱动程序，很好的学习USB驱动语言，以及红外发射器的发射原理参考资料-MFC write USB infrared driver, USB drives good learning language, as well as infrared transmitter launch theory references
SPEED
- 基于飞思卡尔速度检测的程序，原理非常简单，利用红外发射接收管产生脉冲，产生中断，进行速度检测-Based on Freescale' s speed detection procedure, principle is very simple, using infrared transmitting and receiving tubes generated pulses, generate an interrupt, speed of detection
Infrared
- 这是红外发射的电路图，已经用过，很好用的，你们下载后可以直接使用。-This is the infrared emission of the circuit has been used, very good use, you download can be used directly.
hongwai_send_recive
- 基于FPGA的一个红外发射与接收的实验！该方案完全可行！-FPGA-based transmit and receive an infrared experiment! The program entirely feasible!
红外发射
- stm32发射红外信号(no en)
红外解码
- 红外解码，对常用红外遥控发射芯片UPD6121G进行解码，根据接收到波形显示其 32位二进制红外编码数据波形，根据波形下方刻度可查阅每一位为0或1(Infrared decoding, commonly used infrared remote control chip UPD6121G chip decoding, according to receive the waveform display 32 bit binary infrared coded data waveform, ac
stm8s003__V01_IAR
- 采用stm8s003设计的红外发射控制灯程序，此程序已经经过实践，符合要求。(Stm8s003 design of infrared emission control lamp procedures)
119-红外发射原理
- 119-红外发射原理(Infrared emission principle of 119-)
121-双红外发射避障原理测试
- 121-双红外发射避障原理测试(Test of obstacle avoidance principle of 121- dual infrared emission)
120-红外发射原理
- 基于51单片机的基础系统，产生红外线，及发射出相应的红外线程序(Infrared generation and launching program based on 51 single chip microcomputer)