搜索资源列表
crack
- 运用分形制作裂纹-produced using fractal crack
zhonghemoxing
- 用matlab编制的转子裂纹综合模型供做此方面设计的人参考。
MMMNDT
- 该软件主要用于无损检测系统的研究，通过获取的金属裂纹的磁信号判断该金属是否存在裂纹-this software source code was used in metal magnetic memeory non-destructive dection by aquired the signalof the magnetic to discern the position of crack of metal
partition
- 这两个子程序可以对有裂纹的2D和3D单元进行细分，主要用于扩展有限元积分-1.Partition a 2D finite element (triangle or quadrilateral) by a segment 2.Partition a 3D finite element (tetrahedron or hexahedron) by a plane
2013.4.17
- 黄河桥桥梁监控程序，检测桥梁是否危险，裂纹大小-Yellow River Bridge bridge monitoring
AnsysCrack
- Ansys裂纹扩展程序 通过调用APDL模拟裂纹扩展过程-Ansys crack simulation
openxfemPP-1
- 扩展有限元，裂纹扩展,应力强度因子的计算，动态模拟-to solve plate with an edge crack. the code runs for.different mesh sizes and computes the SIF for them.If using these codes for research or industrial purposes.
judge
- 图片裂纹提取包含滤波除燥和图像增强，针对路面图像除去小石子块噪声并提取出裂纹-Image crack extraction includes filtering and image enhancement, removing the small stone block noise and extracting the crack
WM
- 图片裂纹提取包含滤波除燥和图像增强，针对路面图像，判断是否存在裂纹-Image crack extraction contains filtering and image enhancement, to determine whether there is a crack in the pavement image.
BIANYUANTIQU
- 进行基于绝缘子边缘检测与提取,能识别绝缘子裂纹的故障,通用性蛮好-Insulator-based edge detection and extraction, to identify cracks insulator failure, versatility fine
MeshGen
- python 源代码 计算裂纹点以及赋予裂纹点必要的XFEM的自由度-python code for enriching the nodes with additional DOF to fulfill the XFEM heaviside and asympotetic fields functions so as to complete the XFEM priliminary
liewen
- matlab 裂纹检测 检测老师提供的香水瓶上的裂纹，拍摄玻璃瓶图像时，可采用任意方法，酌情处理，只获取裂纹图像即可。-matlab Crack detection
_风力发电机组叶片故障诊断
- 风机叶片的裂纹和断裂是导致风机机组事故的重要因素之一，尽早诊断出风机叶片的 故障部位与故障程度，对安全生产具有意义重大。本文将叶片振动信号作为研究对象，利用小波分解方法对其进行信号分解，并与时域和频域方法处理结果进行对比分析，得出诊断结论。仿真结果表明: 小波分解方法可以更有效的获取故障特征信号，具有较高的故障诊断率。(The crack and fracture of fan blade is one of the important factors that cause the accid
gear mesh stiffness evaluation_energy method
- 利用势能法求齿根裂纹的啮合刚度,可以自行设置裂纹程度，matlab程序求解(This method is used for spur gear and planetary gearbox)
ympm
- 用matlab编写的裂纹碰摩故障方程，可以用来做转子动力学分析(Using matlab to write the crack collision equation, can be used to do rotor dynamics analysis.)
Crackstiffness
- 中性轴法，计算转子轴上裂纹梁单元的惯性矩(Calculate the moments of inertia of the cross section of a cracked beam element based on the neutral axis method)
jianduanweizhitiqu
- 根据二值化裂纹轨迹图像，提取裂纹尖端位置(The crack tip position is extracted from the two valued crack trajectory image.)
CRACK_3D_1.3.16
- 基于ABAQUS的Python二次开发，用于实现复合材料结构腐蚀疲劳裂纹扩展的建模防撞.(based on Abaqus and python secondary development, fulfil composite structures corrosion fatigue crack grow modeling simulation.)
中心裂纹
- 这是一个ABAQUS用户子程序，用于计算化力耦合作用下界面裂纹扩展问题。(The subroution is for simulation of interfacial crack under chemo-mechanical condition implemented in ABAQUS.)
3D cohesive裂纹扩展例子
- cohesive裂纹扩展案例，完整的cae和inp文件,模拟材料内部微裂纹扩展(abaqus cohesive example)