搜索资源列表
LED
- 利用点阵LDE显示一个汉字8 *8。使用C语言编程,利用循环嵌套,其中P0口复用,先送列数据,在送行数据LED1为显示,2位上下滚动,3为左右滚动
led
- 利用单片机P1口实现8个led灯的花样变化-8 led lights microcontroller P1 port pattern changes
PWM_RGB_LED
- Operate RGB led with 3 pwm channel used AVR Mega 8
LED
- 本实验得到的结果为,系统运行起来后,8段数码管一开始就显示1234,一段延时后,显示为2345,再过一段延时后,显示3456,.........。一直延续下去,每个LED显示到9就不显示,之后又重新开始。-The experimental results obtained, the system up and running after the 8 paragraph 1 digital tube display beginning on 1234, after a period of del
C
- 8AT89C52,ADC0809 8路数字电压表测量由A/D转换、数据处理及显示控制等组成,测量0~5V范围内的8路输入电压值,由4位共阳LED数码管轮流显示,最大分辨率0.01V,误差±0.02V。-8AT89C52, ADC0809 8 way digital voltage meter measured by A/D conversion, data processing and display control of the measurement range of 0 ~ 5V inpu
water_led
- 这是一个流水灯的程序,它能够实现8个LED灯的流水式点亮,可以根据频率来决定它流动的快慢-This is a process flow lights, it can achieve the 8 LED lights lit water type can be determined in accordance with the frequency of the speed of its flow
LED
- 基于LPC2210通过GPIO直接控制8个LED产生流水灯效果-GPIO on LPC2210 through direct control of eight LED lights have the effect of flowing water
flowlight
- 8个发光管间隔200ms由上至下,再由下至上,再重复一次,然后全部熄灭再以300ms间隔全部闪烁5次。重复此过程。-8 LED 200ms interval from top to bottom, then bottom, then repeat, and then all go out again to 300ms interval all flashing 5 times. Repeat the process.
1
- 显示小程序 8*8 指示灯 流水灯显示 很经典-Procedures showed 8* 8 LED lights show the classic water
8LEDnixietubeelectronclockprocedure
- AT89C2051只有15个IO口,要显示8位数码管有点吃力,必需扩展,所以找来74HC595串转并移位寄存器,一个做段显一个做位选,只用三个IO口就解决了8+8的显示,如果要再多一点也不怕,不过2051只有2K的存贮空间,也限制了显示位数。DS1302占用3个IO,这样一个P1只用了6个IO,还有两个空着,准备设置一个LED感应自动开关和一个DS18B20,如果程序大小允许再加入红外摇控,把LED显示做大一点,就是一款实用的电子钟。-AT89C2051 only then 15 IO mout
Flow_Led
- 流水灯的设计,使8个LED灯 循环点亮。移动方式可以在模块里面修改-Water lamp design, lit 8 LED lights cycle. Moves inside the module can be modified
LED
- 8个LED分两组,分别实现轮流点亮,给视觉以闪烁感-8 led spit two item, turn on or turn off
swtich-control-LED
- swtich语句的控制P0口8位LED的点亮状态-swtich sentence control P0 mouth 8 LED lightens the condition
LED
- 流水LED灯控制,STC89C52RC;控制8个LED灯顺序循环点亮。-Water LED light control, STC89C52RC;control 8 LED lights lit loop sequence.
LED
- 流水灯实例,8个LED循环点亮,实现流水灯效果(Water lamp example, 8 LED cycle lights, to achieve the effect of water lamp)
VisionShow3.8(中文操作软件)
- 一个LED控制测试软件,可以编辑led样式上传到大屏上(A LED control test software, you can edit led style upload to the big screen)
8.2 LED控制VHDL程序与仿真 2004.8修改
- 8.2 LED控制VHDL程序与仿真 ,FPGA驱动LED静态显示,功能:译码输出模块,LED为共阳接法(8.2 LED control VHDL program and simulation)
7
- 设计两台单片机系统间的串行通信 (1)甲方P1口连接8个LED灯; (2)乙方经串行通信输出数据至甲方,甲方根据所接收的数据,在8个LED灯实现流水灯显示; (3)需采用串行口方式1及中断方式进行数据的发送和接收。(Design of Serial Communication between Two Single Chip Microcomputer Systems (1) Party A's P1 port is connected with 8 LED lights; (2) Pa
LED计算器-完美版-最新修改
- 基于51设计的8位数码管计算器,能实现加减乘除取余根号平方等功能,另外还支持删除操作,这个程序里还有一个亮点就是采用了一个高级5x5键盘设计,支持长按短按和连续按功能,非常值得大家去学习!(Based on the 51-designed 8-digit digital tube calculator, it can realize the functions of addition, subtraction, multiplication and division, and the remai
LED一体箱开发包_V3.9.1.4329_20171031
- 【声明】 此次版本测试 在对 LED03/EP-YTX030 /EP-YTX031,PT-V500/EP-G200/EP-G210 型号做 RS-485通信时 发现有丢包情况,建议客户采用 RJ45传输模式进行控制。如果客户强制使用 RS-485通信,可自己控制 发送指令间隔在200ms以上,可减少丢包率,但是建议客户慎重选择。 V3.9.1.4329_20171031 更新 1、更改 设置音量大小函数参数,规定音量大小的范围在 0-10之间。 2、更改 EP-YTX030 /E