搜索资源列表
GPIO-LED
- GPIO控制LED的简单C程序，希望对大家有所帮助。谢谢大家支持！-GPIO control LED simple C program, we hope to help. Thank you for support!
GPIOINPUT
- 这是关于GPIO输入实验，LED 点灯，让小灯一亮一灭，时间可以自由控制-This is the experiment on the GPIO input, LED light, so light a small lamp to eliminate a time be free to control
LED
- 基于LPC2210通过GPIO直接控制8个LED产生流水灯效果-GPIO on LPC2210 through direct control of eight LED lights have the effect of flowing water
GPIO_module
- 本文件夹中的代码是“GPIO模块”的相应代码。 GPIO_LCM.c 该文件是GPIO模拟时序，实现SPI协议的代码。 GPIO.pdf 该文件是C6713的GPIO连接LED和LCM模块的原理图，至于C6713的其他部分（如SDRAM、FLASH等）和部分控制信号、电源信号都略去。读者朋友可参考另外相关的章节。 -The code in this folder is " GPIO module" of the corresponding code.
GPIOdirver
- GPIO的流驱动代码，附有可以进行LED调试的例子-GPIO flow-driven code debug LED can be attached to the example
Gpio LEd for redbull
- mp3 player for firebull
GPIO-LED-V1.0_OK
- STM32 GPIO LED OK OK BOARD-STM32 GPIO LED OK OK BOARD
gpio-debug
- gpio调试包括led闪烁，按键输入实现IO的输入输出,即跑马灯和按键功能.左右按键负责控制跑马灯方向,上下控制速度. -gpio debug
EX01_GPIO_LED
- dsp 2812 GPIO口的LED灯的暗灭显示-GPIO AND LED CROL
GpioToggle
- 该程序主要是用f2812来点亮LED灯。其中程序中采用了3种方式对Gpio进行操作。-The program is mainly to light LEDs lamp by f2812. Which the program uses three kinds of ways Gpio operation.
1-GPIO-led
- 超核源码1-GPIO小灯实验 超核源码1-GPIO小灯实验-lED control for feskale K60
Blinker
- Using IAR for GPIO of STM8 to toggle led on PIND3
gpio_mio
- ZYNQ 的gpio 可以通过MIO 引出到PS 端的引脚，本例子 的gpio 通过MIO 引出，控制LED 灯D29。-ZYNQ GPIO can be drawn to the PS through the MIO pin, this example GPIO led by MIO, control LED lamp D29.
gpio
- 基于DSP2812，使用GPIO的引脚来控制LED灯闪烁。即控制XF引脚高低电平不断变化。(Based on the DSP2812, the GPIO pin is used to control the LED flashes. The XF pin is constantly changing between high and low levels.)
GPIO
- Blink LED using timer delay in Nuvoton controller
12-GPIO输出—使用固件库点亮LED灯
- STM32点亮LED灯2313122332(The HA is according to the time of the story of the world)
LED KEY
- LPC5411XLED流水灯, 实现轮询闪烁。可以控制闪烁时间，key健。所有LPC82x器件的存储器映射都相同。不同的LPC82x器件支持不同的闪存和SRAM存储器大小。(GPIO registers support up to 32 pins on each port. Depending on the device and package type, a subset of those pins may be available, and the unused bits in GPIO r
实验1 - GPIO驱动LED
- 艾克姆开发板例程，驱动GPIO点亮led(ACM development board routines, drive GPIO to light LED)
STM8S-A01_GPIO基础知识
- 在IAR开发环境下，通过STM8S芯片，控制GPIO点亮LED(Use GPIO light up the LED)
1-GPIO
- 此例程是利用XC886单片机通用IO口实现LED闪烁的实验。(This file contains the Project initialization function.)