搜索资源列表
PortCon
- 单片机的并口调试软件的源代码，调试单片机编程器的话是很有用的-SCM Parallel Port Debugging software source code, debugging single-chip programmer, then it is very useful
并口-CAN实验装置的VB界面设计
- 基于并口-CAN实验装置的VB界面设计,主要是VB6的源代码,不能直接运行，因为没有硬件实验装置,运行结果为不可预测.使用并口前请在BIOS中设置并口:378H,EPP等.-Based on the experimental device parallel-CAN interface design of the VB is mainly VB6 source code, can not directly run, because there is no experimental device h
EEPROM
- 电可擦除可编程只读存储器EEPROM可分为并行和串行两大类。并行EEPROM在读写数据是通过8位数据总线传输，而串行EEPROM的数据是一位一位的传输。虽然与并行EEPROM相比，串行传输数据较慢，但它体积小、专用I/O口少、低廉、电路简单等优点，因此广泛用于智能仪器、仪表设备中。-Electrically erasable programmable read-only memory EEPROM can be divided into two major categories of paral
iodemo
- dos系统并口用作io功能的小程序，dos系统并口用作io功能的小程序-dos system parallel port io functions for small procedures, dos system parallel port io functions for small program
jflash.h3900.tar
- jflash for h3900 - A utility to program Intel flash devices from a PC parallel port. -jflash for h3900- A utility to program Intel flash devices from a PC parallel port.
FlexPortTest
- 发送01~08到并口去实现电脑控制8路开关的功能。-Send 01 ~ 08 to the parallel port to realize computer-controlled 8-way switch functions.
stm32_jtag
- STM32的仿真器可以用简易的并口来开发，要求安装HJTAG软件，要求IAR版本5.2以上-STM32 Emulator simple parallel port can be used to develop, require the installation of HJTAG software, version 5.2 and above requirements of IAR
kkk
- 实现pc机器的，并口功能。而且可以满足大多人的需求-The realization of the machine pc, parallel port function. And meet the needs of most people
ParallelPortTest2
- 利用ntport libray实现的计算机并口位输入输出测试程序源码。-Ntport libray achieved using computer parallel port digital input and output test procedure source.
POS58LDLL1.1
- 利用VC6.0，非MFC,实现PC串并口,打开，关闭，读，写操作的动态库-Use VC6.0, non-MFC, the realization of PC parallel port string, open, closed, read, write, operate a dynamic library
ParellelPortLcd1602Driver
- 用并口去驱动液晶屏LCD1602的源代码，把并口当单片机IO口来用-Using parallel port to drive LCD LCD1602 the source code, the parallel port when the single-chip IO port to use
SJF2440
- 从PC机并口通过JTAG烧写S3C2440的程序源码。这是一个Vistual Studio C++工程。-Machine from the PC parallel port JTAG programmer through the process S3C2440 source. This is a Vistual Studio C++ Works.
sjf2410forwigglerJTAGcode
- sjf2410不支持wiggler下载，主要是并口所用的数据线定义不同，主要修改JTAG.H头文件里的定义。若并口地址也不是常用的则也需要修改相应文件。 Visual C++环境编译 修改部分如下所示 #define TCK_H 0x04// 0x01 #define TDI_H 0x08// 0x02 #define TMS_H 0x02// 0x04-sjf2410 does not support download wiggler is mainly used for
parport_Windows_driver_WDM
- 鼠标Windows驱动，开发工具WinDDK-Parallel port driver for windows, tools: winddk
EasyParallel
- 本程序演示如何使用WinIO向并口发送十六进制代码。-This procedure demonstrates how to use the parallel port to send WinIO hex code.
bingkou
- 基于89s52的并口显示程序，使用三位数码管，用74ls245做驱动。-89s52 shows the parallel port-based procedures, the use of three digital tube, to do with 74ls245 drive.
zizhi-ATMEGA16-bianchengqi
- 自制的最简单的avr的编程器，需要使用并口。-Made the simplest avr programming, and need to use the parallel port.
Console
- It counts the input ttl frequency at the s5 bit of parallel port using ntport library.
dmapara.ZIP
- Very fast file transfer over the parallel port, using dma and fifo, fast and slow methods. It works in dos and windows. It works in nt , if you use a program to open the ports so as winio. I have achived rates of 750 kbytes/sec in the fifo mode. The
ROBO
- to activate a robot or parallel port data pin this code can be used or to send data to printer port. I had used this code to move a robot right, left, back, front. rajesh.f - INDIA rajesh1983jan10@yahoo.com-to activate a robot or parallel port data p