搜索资源列表
TMS320C6000DSP
- 《TMS320C6000 DSP实用技术与开发案例》针对目前的DSP系统设计,以TI公司的C6000数字信号处理器为硬件平台,详细地介绍了用DSP作为微处理器核的系统的各种工程和算法实现-"TMS320C6000 DSP development of practical techniques and case" for addressing the current DSP system design, in order to TI s C6000 digital signal processor
GPIO
- DSP GPIO程序通用输入输出接口 可以外扩其它硬件-DSP GPIO
6713_FPGA
- DSP+FPGA+USB2.0板子电路图 DSP是6713;FPGA是XilinxXC2S200;USB芯片是CY68013A-128AXC-DSP+ FPGA+ USB2.0 circuit board DSP is 6713 FPGA is XilinxXC2S200 USB chip is CY68013A-128AXC
DSP_Builder72_SP3
- 本文介紹破解DSP Builder 7.2 SP3詳細步驟-This article describes the DSP Builder 7.2 SP3 crack detailed steps
DPSK
- 很好的DSP5416学习的程序,实验可以完全通过的,提高DSP水平很有帮助-DSP5416 a good learning process, experiments can be fully adopted by the DSP to improve the level of useful
yuyinlvfangshiyan
- 基于DSP语音录放实验,基于TI C5416平台实现!-DSP-based audio playback experiments, based on the TI C5416 platform!
dsp_rar
- DSP开发工具Code Compile Studio(CCS)开发数字信号处理程序DSP——实现IIR滤波器,IIR高通、低通、带通。-With DSP tool Code Compile Studio(CCS),develop a program for DSP,which it can be a highpass,lowpass,bandpass.
demodulateur_FM2
- FM demodulator with dsp tools xilinx system generetor for dsp.
FFT
- TMS320C54X DSP FFT 程序,希望对大家有用。-TMS320C54X DSP FFT procedures in the hope for all of us.
dsp
- 信号调制与解调,使用ccs开发工具,使用ti 的dsp5402板-Signal modulation and demodulation, use the ccs development tools, the use of ti' s dsp5402 board
Fdpcli10
- 一个人脸检测系统的相关代码,使用了STL技术,服务器程序是基于ARM+DSP-A face detection system, the relevant code that uses the STL technology, the server program is based on ARM+ DSP
ADS831-DSP
- 描述了ADS831E与DSP的相关接口及使用方法。-Describes the ADS831E with DSP-related interfaces, and use.
DSP
- 【摘 要】为了减少集成电路硬件复杂度,针对QAM 调制软件实现速度慢的问题,在分析MQAM 调制原理的基础上,采用 直接频率合成实现正余弦信号及无时延改进的滤波器编程方法,提出一种快速实现MQAM 调制算法的软件编程思想,并以 TMS320C55X 为平台[1,4],将MQAM 调制算法进行了C 编程实现。结果表明:该编程方法能快速产生MQAM 调制信号。 【关键词】多电平正交幅度调制;脉冲成形滤波器;直接频率合成;数字信号处理-【Abstract】 In order to redu
dsp-book
- High-Performance DSP Using Virtex-4 FPGAs,very detail-High-Performance DSP Using Virtex-4 FPGAs, very detail
37724125UPS-500W
- The 2812 figure to do their own power DSP procedures for their own power to do the 2812 figure DSP program
5502_wdg
- 5502的看门狗程序,CCS3.1开发。DSP的看门狗输出信号管脚需要外部连接到复位线上才能起作用。-5502' s watchdog program, CCS3.1 development. DSP-Watchdog output signal pin connected to the need for external reset line to work.
QuickEmbed
- Enhanced XDS510 USB Emulator Driver (QuickEmbed) for ti dsp Programmers
dsp
- 一些有助于学习dsp的形象的教程性的程序-That will help to learn dsp easily
Study-on-Starting-up-Method-of-PMSM-Based-on-Hybri
- 基于复合式光电编码器永磁同步电机启动方法的研究 简述了复合式光电编码器的工作原理,分析现有永磁同步电机转子位置检测方法的不足,提出了使用复合式光电编码器对永磁同步电机转子初始位置检测及电机启动的方法,最后通过以数字信号处理器(DSP)为核心的实验平台进行实验,实验结果表明,该方法可以满足实际使用的要求,实现了电机可靠启动、运行。-The operating principle of hybrid grating encoder was introduced and the shortcomi
dsp_f2812_spi
- 本程序为DSP应用程序,为F2812系列SPI模块使用范例,本程序在CCS2000上编译通过,并在开发板上调试成功。-This procedure for the DSP application, for the F2812 Series SPI module examples, this program CCS2000 compiled by, and in the development of a successful board debugging.