搜索资源列表
2C3
- 程序说明: 1.本程序实现了对字母顶点设定材质的设置; 2.本程序实现了对数字顶点设定材质的设置; 3.本程序实现了对所有顶点打光; 4.本程序实现了8个移动的光源; 5.环境光为全黑。 操作说明: 按1:开启/关闭平行光(默认关闭) 按2:开启/关闭点光灯(默认开启) 按3:开启/关闭聚光灯(默认关闭) 按4:开启/关闭萤火虫效果(默认关闭) 按5:开启/关闭Material1(默认开启) 按6:开启/关闭Material2(默
traffic
- 假设道路交叉口,有红绿黄三色交通控制灯,且要求: 1)。绿灯亮是,车辆可潜行,过30秒,绿灯熄灭,黄灯亮; 2)。黄灯亮5秒后,熄灭,红灯亮,车辆停止前行。红灯亮30秒之后熄灭,黄灯亮; 3)黄灯亮5秒之后,熄灭,绿灯又亮,车辆可通行,如此循环。 -Assuming the road intersection, a red-green-yellow three-color traffic control lights, and requirements: 1).
ScanTool
- PC上汽车故障诊断程序源代码,加上很简单的硬件电路后就能跟多种车型通信,获取汽车上的故障码、实时数据流。-ScanTool.net OBD-II Software for ElmScan is free software that allows you to use your computer and an inexpensive hardware interface to read information from your car s computer. Current vers
dingshiqi
- 可以利用定时器实现LED的亮灭,使你快速掌握定时器的应用!可用proteus仿真,值得下载!-Can use the LED' s light off Timer, Timer allows you to quickly master the application! Free proteus simulation, it is worth to download!
qiehuan
- 51单片机,用两个按键分别控制LED的不同闪烁方式和亮灭-51 MCU, with two buttons control different LED flashing light off
liangmie
- C51单片机用按键控制LED的亮灭,用中断作定时器控制LED亮灭时间-C51 MCU control button LED lights off, using interrupt timer control LED light off
Point
- VHDL语言实现在16*16点阵显示模块上显示汉字。(EDA/SOPC开发平台)显示内容未输入,形式为16位字符串(0、1)显示0时对应点阵上的灯亮起,1的时候熄灭-VHDL language to display Chinese font on a 16 x 16 dot matrix display module. (EDA/SOPC development platform) , the form of a 16-bit string (0,1) “0”stand for light on
controlLED
- 本程序包含两部分,一部分是上位机用VC写的,通过usb通信来控制开发板上的LED的亮灭。另一部分时EZ-USB固件程序。-This program contains two parts, one written by the host computer using VC usb communication to control development board LED light off. Another part of the EZ-USB firmware.
light_show
- android控制arduino led亮灭-android control arduino led light off
ex1
- 使用EDA实验箱上的脉冲,进行分频,通过波形仿真和观测实验箱上输出指示模块中的OUT1红色LED(发光二极管)的亮灭时间来验证是否符合设计要求。-Using the the EDA experimental box on the pulse divide output by the waveform simulation and observations on the experimental box the indication module OUT1 red LED (light emitt
PAOMADENG
- 该程序实现LED的闪烁,每隔0.2秒更替一次亮灭-The program LED flashes every 0.2 seconds replacement light off
Lights-synchronized-flow
- 八个发光二极管先同时亮灭两次,再从右向左依次灭,再从左向右依次灭-Eight light-emitting diode light off twice while first, and then turn off right to left, left to right and then turn off
no.2
- AT89C51单片机,实现一个开关控制一个LED灯的亮灭-AT89C51 single-chip, to achieve a switch control an LED light off
2013_work_3
- 1、使用T0或T1,完成基准为50ms的定时,使用查询方式完成即可; 2、利用50ms的基准定时,完成1s定时,每1秒,切换EZ-51开发板上某个LED(如LED0)的亮灭状态; 3、每10秒,控制EZ-51开发板上的蜂鸣器鸣叫1次; 4、分别用汇编和C51完成上述要求。-1, using the T0 or T1, the timing of completion basis of 50ms, can be accomplished using the query 2, usin
STC89c52
- 用89c52控制8个LED灯,使LED灯从左到右依次亮灭,包含中断程序-With 89c52 control 8 LED lights,From left to right so that the LED light off, including the interrupt routine.
webpage-control-zigbees-led
- 本程序实现静态网页控制zigbee的led亮灭,实现zigbee与arn的结合-The program s static pages control zigbee led light off, realize the combination of zigbee with arn
led_control(receive)
- VC++通过串口自定义通信协议控制LED等亮灭。-VC++ LED light off and other custom communication protocol via the serial control.
led_control(send)
- vc++通过自定义通信协议控制LED灯亮灭(Send端)-VC++ LED light off and other custom communication protocol via the serial control(send).
traffic_simple
- 基于Verilog的简易交通灯控制。//主干道绿灯亮30s,最后5秒绿灯灭黄灯亮,30s过后红灯亮起,倒数20s后绿灯亮30s,如此重复 //支干道红灯亮30s,后绿灯亮,支干道绿灯倒数20s,最后5s绿灯灭黄灯亮,20s倒数完后换红灯亮30s,如此重复-Verilog-based simple traffic light control. // Main road green light 30s, the last five seconds off the yellow light gre
Light-Ctr
- 楼梯开关灯设计,楼上时可在楼上关灯,下楼时可在楼下关灯-Staircase light switch design, can turn off the lights when upstairs upstairs, downstairs to turn off the lights downstairs