搜索资源列表
10000seconds-yinei-de-jishichengxu
- 这是10000秒以内的计时程序,用数码管进行显示是参考书目上的程序,当然奥,希望对您有用奥-THIS IS THE TIME PROGRAM ,
Linux-74HC595-6410
- linux下的74HC595驱动程序,能够驱动数码管6410平台下验证通过-the Driver of 74HC595 on Linux 6410 platform
6410-Digital-LED--for-linux
- 在Linux下写的74HC595的驱动程序,用于控制数码管-Write the 74HC595 driver under Linux, used to control digital tube
shumaguan
- 单片机下数码管局部显示代码欢迎大件下载测试-Single-chip digital tube under local code welcome large download test
DE2_70_NIOS_DEVICE_LED
- 关于DE2_70板子作为usbslave连接到pc机上,pc作为host端向DE2_70发送数据包,当DE2_70收到数据包时其上led数码管一次数字(依次累加),其中它的fireware可以作为我们移植ISP1362 Device Controller Driver到uClinux的参考-The DE2_70 board as usbslave, connected to the pc, pc as the host side to send packets to DE2_70 When DE
hp
- 基于89C52单片机,驱动LED数码管实现100-0循环倒计时的C源代码-Based on the 89C52 microcontroller, drive LED digital tube 100-0 cycle countdown C source code
AD
- 瑞萨单片机的AD使用,能检测外部可调电位器的的电压值,用8段数码管显示电压值。-Renesas MCU AD use, can be detected externally adjustable potentiometer voltage value, with 8 digital tube display voltage values.
MCU
- 4*4扫描键盘,在8段数码管上显示,AT89C51+74HC595-4* 4 keyboard scan in 8 digital tube display
digital8421shumaguan
- digital数码管-8421 digital
Electronic-calendar
- 这是一款用multisim画图而成的数字万年历,月日的各位用七段数码管显示,十位用LED的亮灭显示。星期用七段数码管显示。-This is a drawing made with multisim digital calendar, you use the day of the seven-segment LED display, ten off with bright LED display. Week segment digital tube display.
XX
- 外中断计数2位数码管显示,亲测可用,有需要来拿-External interrupt count two digital display, pro-test is available, there is a need to come and collect
ww
- 29-原创VB上位机控制数码管,亲姊妹实验,次来分享。希望有用。-29- original VB PC digital control, pro sisters experiment times to share. I hope useful.
DS18B20-and-digital-display
- DS18B20和数码管显示,程序已经调试成功,可以正常使用-DS18B20 and digital display, the program has been successful debugging, you can normally use
program
- 主要是ad转换的,通过棉线粗细和电压的关系式,最终数码管显示棉线的粗细,还有蜂鸣器报警-Mainly ad conversion by thread thickness and voltage relationship, and ultimately digital display thread thickness, as well as buzzer alarm
Traffic
- 内容:1、程序目的:使用定时器学习 倒计时 红绿灯原理 主要程序与倒计时相同 2、硬件要求:数码管、晶振12M 3、P1口连接至LED用于显示红绿灯(p1接锁存器,八段数码管的位信号和断信号都通过p1口锁存起来,这样可以节省端口) 4、数码管用于显示时间-Contents: 1, the program purpose: to learn to use the countdown timer with countdown traffic light principl
press_counter
- 基于verilog 的按键计数程序,约束文件对应的是BASYS2 的 FPGA开发板,注意数码管对应的管脚分配-Press count program based on Verilog
Traxffic-new
- QTH9054 微机试验箱红绿灯模拟源代码,通过8255操作LED灯和数码管模拟红绿灯-QTH9054 microcomputer test box traffic simulation source code, the simulation traffic light through the 8255 operation LED lights and digital tube
ds18b20102
- 温度测试 DS18B20精确计算,含一位小数, 液晶显示,用的是独立的液晶板,数码管动态显示被测温度值-温度测试 DS18B20精确计算,含一位小数, 液晶显示,用的是独立的液晶板
ADCPDMA
- ADC+DMA+595 采样数据显示数码管-ADC+DMA+595 sample
10000seconds-yinei-de-jishichengxu
- 这是10000秒以内的计时程序,用数码管进行显示是参考书目上的程序,当然奥,希望对您有用奥-THIS IS THE TIME PROGRAM ,