搜索资源列表
gpio1
- 利用开发板上的/dev/mem设备,进行内存映射,驱动cpu的GPIO口,点亮和熄灭led灯.附makefile文件-use development board / dev / mem equipment, memory mapping, Drivers cpu GPIO the mouth, and the lights extinguished led lights. makefile attached document
arm_led_interrupt
- 在s3c6410上实现采用中断按键控制led灯点亮，裸板驱动(c语言)-to bright the led with c throght loop
LED1
- 能让ARM控制的LED小灯循环点亮,是裸机程序。-ARM allows the control of small LED lights cycle of light, is the bare metal process.
A
- 用电平开关的输出作为中断源，每个开关对应于一个中断源。在中断服务程序中，通过74LS273输出一个数据，以点亮与中断源相对应位置的LED。-The output power level as the interrupt source switch, each switch corresponds to an interrupt source. The interrupt service program, a data output through the 74LS273 to light cor
button
- 利用fs2410开发板上的一个按钮，在linux下点亮一个led灯得驱动程序-Fs2410 development board using a button in linux too light a lamp led driver
leds
- 三星s3c2440 中 arm 实验， c实现 led灯点亮-arm experiment, and c to achieve led lamp lights up
ASAMPLE2
- 基于51单片机的led 等的显示 以及循环点亮-achieve 51
s5pc100
- 利用平台设备机制，对s5pc100实现按键对Led灯的控制，按下点亮，松开熄灭-Use platform equipment mechanism to realize s5pc100 buttons on the control of Led lights, press the light, loosen put out
drv_dv_platform_gpio_a
- GPIO实现LED驱动， 把LED等一个一个的点亮-GPIO LED driver, LED and other light
i4
- 此程序用ARM9点亮四个led，并循环灭和亮。-This procedure is lit four led, and cycle off and lit. . . . .
gpio
- gpio，arm裸板点亮一个led灯的程序。不过没有前面的初始化。-gpio light a led lamp arm bare board procedures. However, no previous initialization.
wenduji
- 用ARM9（s3c2410）设计一个温度监测仪。当温度超过报警温度时，LED报警灯点亮；按下回车键，开始工作；按下按键K10，温度监测仪停止工作；正常温度温度计的水银柱颜色为蓝色，反之，为红色。-ARM9 (s3c2410) design a temperature monitor. When the temperature exceeds the alarm temperature, LED warning lights lit press the Enter key to begin wo
am335x_ledDriver
- 基于TI的am335x CPU编写的一个LED驱动程序(基于linux)，用于点亮一个LED-LED driver for the CPU of am335x in the linux environment
swtichled
- swtich语句控制P0口8位LED流水灯点亮状态,使用C语言的swtich语句控制P0口8位LED流水灯的点亮状态-swtich statement P0 port 8 LED lights lit state swtich statement using the C language control P0 port 8 LED lights are lit
ledlight
- C程序LED流水灯点亮代码，使用P0口流水点亮8位LED，是一段实用的代码，而且代码也较少。-C program LED lights light up the code, use the P0 port running water is lit 8 LED is a period of practical code, and the code is less.
KEY_INT
- 基于2410的中断实验，按下键之后触发中断led灯点亮-Based on the 2410 interrupt experiments
LEDTesting2
- s3c2410 板上实现QT控制LED灯，实现LED灯一一对应的点亮也可实现随机点亮。此次设计为本科生字符驱动编写的程序，经过运行和检验完全正确，使用版本为QT4.6-s3c2410 board realized QT control LED lights, LED lights illuminate one correspondence can also be achieved randomly lit. The design for undergraduate programs writte
user_led
- ADS1.2在试验箱的CPU板上点亮LED，并轮流闪烁。-ADS1.2 the CPU board in the chamber lit LED, and turns flashing.
led
- OK6410 led跑马灯裸机程序。下载到开发板后可看到LED轮流被点亮，不断循环。-the led program for OK6410
LED
- 点亮P1口的一个LED灯 该程序是单片机学习中最简单最基础的， 通过程序了解如何控制端口的高低电平-A leds light up P1 mouth The program is the basis of a microcontroller learning one of the most simple, Through the application to know how to control the high and low level of port