搜索资源列表
8255控制循环LED显示
- 一个采用8255芯片控制8个LED灯循环点亮的程序代码-a 8255 chip used to control eight LED lights lit circle code
jz
- 甲乙两台80C51单片机串行通信,一台通过开关控制P1口的高低电平并发送数据,另一台接收发送过来的数据,通过P1口用发光二极管显示,高电平点亮,低电平熄灭。-A and B two 80C51 microcontroller serial communication, a switch control through the high-low P1 port and send the data to send over another to receive the data, through t
c
- CC2430串口发送以及led灯的点亮,同时还有温度控制程序-CC2430 serial send
controling-of-lights
- 下位机通过串口接收数据并降该数据作为switch语句变量对应到不同的函数产生相应的现象,例如当按下全亮按钮时,通过下位机程序控制LED灯使LED灯全亮。 当鼠标勾选单灯控制区复选按钮时,同理通过串口传输数据,相应的LED点亮,取消勾选后该灯熄灭。 当鼠标点击流水灯控制区某个单选按钮时,上位机将数据通过串口送至下位机,下位机根据数据相应调节流水灯延时函数变量,完成控制流水灯速度的功能。 -Lower computer through the serial port to receive
LEDControl
- 控制LED屏 ,点亮LED,关闭LED 修改LED_1_ON就可以对所有的LED进行操作-Control the LED screen, lit LED, turn off the LED changes LED_1_ON can operate all of the LED
URAT
- 一个简单的串口通信汇编程序,通过上位机发送控制信号控制单片机LED灯的点亮与否。文件有protues仿真电路与hex文件。调试时请下载串口调试助手,端口Com1,波特率96-A simple serial communication assembler, through the host computer sends control signals control the chip LED lamp is lit or not. Documents protues Simulation ci
SourceCode
- 实现自定义的USB编程。启用了D12的端 点1和端点2,端点1为中断传输,最大包为16字节,查询间隔为10ms。端点2为批量 传输,最大包为64字节。端点1的输出第一个字节为控制END USB板上的LED的,每个 bit代表一个LED,为1时表示对应的LED亮。端点1的输入第一个字节为返回的开关 状态,每个bit代表一个按键,为时表示对应的按键按下。输出端点2的数据通过串 口发送出去,串口接收到的数据通过端点2返回。-Implement custom USB programm
Desktop
- 很好的单片机程序,用于点亮LED灯,很适合初学者-Good SCM procedures for light LED lights, it is suitable for beginners
ep1c12_1_led_test
- 描述一个简单点亮LED灯的程。适用FPGA作为IO口测试用-Describe a simple light leds. Apply FPGA as IO mouth test
00ic_PWM_LED
- 使用PEM通知led灯点亮时间和熄灭时间 间接观察PWM原理(Indirect observation of PWM principle by using PEM to notify LED lights and extinguish time)
led
- 点亮LED程序 用于PCB板测试,检查PCB板健康状态(The LED program is used to test the PCB board and check the health status of the PCB board)
4.1.1:nrf52832-LED
- 操作gpio引脚点亮LED,学习简单的操作nrf52832芯片的gpio引脚。(Operate GPIO pin to light LED, learn simple operation of nrf52832 chip GPIO pin.)