搜索资源列表
msp430shujucaijixitong
- msp430f149实现的数据采集系统 结构简单 功耗低 模拟采集传感器 数字开关量采集 串口通讯UART模块 电源供电及复位-Executable files built outside of IAR Embedded Workbench Follow these steps to load and debug an executable file that was built outside IAR Embedded Workbench, for example p
PC-jieshou
- msp430f149单片机与nrf905之间实现串口通信，已做个试验验证过。-msp430f149 between MCU and nrf905 serial communication has proven to be a pilot.
MCU-fasong
- msp430f149单片机与nrf905串口通信，这是发送节点的c语音程序-msp430f149 MCU and nrf905 serial communication, which is sending node c voice procedures
DHT21_MSP430F149
- 基于MSP430F149的温湿度传感器DHT21（又名AM2301）控制程序。 说明：空闲时单片机处于LPM3,若串口收到有效命令唤醒单片机开启采集，温湿度值以字符形式发送到串口，用串口调试助手即可观察。-Temperature and humidity sensors based on MSP430F149 DHT21 (also known as AM2301) control procedures. Note: when the MCU is in idle LPM3, if the
xxx
- //MSP430F149串口行实验程序 //使用ADC12采集实验,将采集到数据送向PC.(序列单次采集,采用定时器A作为时钟源) //P3.4为发送,P3.5为接收 晶体使32768HZ/8MHZ. 串行波特率B/S //使用SMCLK作为波特率发器时,不能使用LPM2,LPM3! -msp mcu c programming...
6-2
- 用于MSP430F149。从串口接收数据，分析收到的数据包，然后根据算法进行运算，最后将结果从串口返回。 -For MSP430F149. Receive data from serial analysis of received packets, and then computing algorithm, and finally return the results from the serial port.
7MSP430F149-use-USART1-to-define-P4
- 使用MSP430F149芯片，透过串口与电脑通信，波特率9600,8数据，无校验。使用32.768k晶振，使用P3.6和P3.7口作为发送和接收口，使用异步通信USART1，采用查询形式。实现通信，当单片机接收到以S结尾以W开始的字符串时，单片机会把中间的数据赋值给P4口。-MSP430F149 chip through the serial port to communicate with the computer, baud rate 9600 data, no parity. 32.768
NRF24L01P
- 1． <MCU-fasong>发送端固定发送0x01,0x02……0x32,32字节数据 2． <PC-jieshou>接收端串口和PC连，当接收到后，打开串口助手或者超级终端软件，对接收到数据进行检验， 当接收到的也是0x01,0x02……0x32,32字节数据表示接收正确 其中波特率选择9600 3.晶振使用XT2 8M,测试环境MSP430F149-1. <MCU-fasong> Sending end is fixed to sen
msp430_uart
- MSP430F149单片机嵌入式编程，串口通讯程序，中断接收后发送。-MSP430F149 microcontroller embedded programming, serial communication program，after receiving the interrupt to send.
430-UART0-GPRS-UART0-430
- 430-UART0-GPRS-UART0-430串口通信(430-UART0-GPRS-UART0-430 serial communication)