搜索资源列表
KeilC5119264LCDdriver
- 液晶显示子程序,Keil C51编写的19264液晶片驱动程序。-LCD subroutine, Keil C51 prepared by the 19,264-LCD driver.
kongwen
- 对8051cf020的温度控制和液晶显示急串口上传的代码-8051cf020 the right temperature control and LCD urgent Serial upload code
km12232f
- 液晶中文显示串行驱动程序,代码精简,思路清晰,非常实用-LCD Chinese Display Serial Driver, code simplification, with clear ideas, very practical
uart+lcm13
- 是用C语言编写的关于用51单片机控制12864液晶LCD的源程序,适用与交流电压及其谐波的显示
LCD-display
- lcd显示程序,为430代码-LCD display program for the 430 code
STC51-MCUs-communication
- 本程序实现了基于51单片机的多机串行通讯:通过主机对从机操作读取获得挂于从机的温度传感器DS18B20温度值显示于主机控制的液晶屏。-This program implements the serial communication based on 51 single-chip multi-machine: by the host to read from the operating temperature sensor DS18B20 temperature hanging slave T
30
- 驱动12232液晶模块显示中文,显示清晰,字体为简体中文-12232 LCD display module drivers English, show a clear, fonts for the Chinese
MBmagCPV3.1
- 485多机通信+lcd液晶显示,内附源码及电路仿真(我自己做的,我也是初学,)-More than 485 communication+ lcd liquid crystal display, containing source code and circuit emulation (I do, I am also a beginner,)
yejingchuankou
- 12864液晶显示模块测试汇编程序(单屏 PSB)串口驱动-12864 LCD Module compiled the test program (single-screen PSB) serial driver
lcdd
- 串口通信程序及LCD显示程序 串口通信程序及LCD显示程序-Serial Communication
chuankou
- f340程序,用于串口接受数据,液晶显示数据,串口返回接受到的数据-f340 procedures for the serial port to accept data, LCD data, serial data back to receive
sample2
- 条形码扫描处理应用程序,应用PS/2串口处理,并能进行LCD显示。-barcode reading purogram
the-source-code-of-electronic-scale
- (1)初始化定时器与中断控制寄存器,初始化液晶显示器,设置串口通信波特率。 (2)启动双积分AD转换过程,循环读取反向积分的计数值N,根据式3-7算出反向积分的计时值T2,换算出荷载重量值,送LCD显示。 (3)每次换算出荷载重量值后,判断荷载是否超量程,如果超过系统量程2kg,则启动蜂鸣器报警。当荷载卸载至2kg以下后,解除报警。 (4)如果有校准按键被按下,则响应外部中断0并查询按键编号,执行相应校准程序。 (5)如果上位机软件STP_ISP发送了在线控制命令,则响应串口中断
electronic-scale
- (1)初始化定时器与中断控制寄存器,初始化液晶显示器,设置串口通信波特率。 (2)启动双积分AD转换过程,循环读取反向积分的计数值N,根据式3-7算出反向积分的计时值T2,换算出荷载重量值,送LCD显示。 (3)每次换算出荷载重量值后,判断荷载是否超量程,如果超过系统量程2kg,则启动蜂鸣器报警。当荷载卸载至2kg以下后,解除报警。 (4)如果有校准按键被按下,则响应外部中断0并查询按键编号,执行相应校准程序。 (5)如果上位机软件STP_ISP发送了在线控制命令,则响应串口中断
uart0
- 实现ADC0采样芯片温度,通过LCD显示,并通过串口0(J13)发送到PC机,同时接收PC传回的一个字符并显示, 请使用串口调试工具调试!-ADC0 sampling chip temperature, LCD display, and display through the serial port (J13) is sent to the PC, while receiving the character of the PC returns Please use the seria
TC35call
- 手机打电话的工程,包括通讯模块以及LCD显示模块等-Cell phone works, including the communication module and LCD display module
lcd
- 52单片机与PC机通信,通过软件助手给单片机发送数据,利用lcd屏显示数据-52 microcontroller and the PC communication software assistant to the microcontroller to send data using the lcd screen to display data
SerialDisplay
- 串口连接16针LCD显示,单片机控制。可用RFID显示-Serial port to connect a 16-pin LCD display, single-chip control
add
- 串口计算器,可以实现加、减、乘、除、括号、sin()、cos()等基础运算,支持浮点数和整数,以LCD显示,有报警功能。-Serial calculator can add, subtract, multiply, divide, brackets, sin (), cos () and other basic operations, support for floating point and integer, with LCD display, alarm function.
OLED显示(模拟SPI总线)2
- 单片机nrf82532驱动液晶屏,使用串口驱动程序,很好是节约单片机输出口。(The single-chip nrf82532 drives the LCD screen and USES the serial driver, which is very good to save the single chip.)