搜索资源列表
如何编写Vxworks 设备驱动程序
- 如何编写Vxworks 设备驱动程序，不错的文章-It introduces how to write the device driver in VxWorks.
keil驱动程序编写
- keil下驱动程序的编写，VC-the driver prepared, VC
s3c44b0 + 29lv160 jtag下载程序编写
- s3c44b0 + 29lv160 jtag下载程序编写，要想下载到别的型号FLASH，请改写相应代码。-s3c44b0 29lv160 JTAG download prepared, in order to download other FLASH models, the corresponding code rewrite.
ISD176.1720的经典程序，实现了1720的几乎所有功能
- 1720的经典程序，实现了1720的几乎所有功能，程序编写标准,1720 classic procedures, to achieve the 1720 almost all the functions, procedures for the preparation of standards
51程序集
- 里面有好多的原码,大家都来下载.用asm编写的-There are a lot of the original code, for everyone to download. Prepared with asm
PCB
- 华为的印刷电路板（PCB）设计规范，程序编写规范等-Huawei’s printed circuit board (PCB) design specifications, programming specifications, etc.
240_128_LCD_driver_and_multi-level_menu
- 240*180液晶的应用示例，由按键控制翻页和菜单的选择。本程序提供了一种处理复杂菜单程序编写的方法，是很好的参考资料。-240* 180 LCD application example, control the next page from the buttons and menu choices. This program provides a menu to handle complex programming method is a good reference.
dsp28335 循环数据缓冲器 C代码编写
- dsp28335 循环数据缓冲器 C代码编写 使用UART 循环缓冲区的程序编写
AVR编写1628.C程序
- AVR编写1628.C程序
51编写1628.C程序
- 51编写1628.C程序
用c实现按键的状态分析法的程序
- 本程序就是非常有用的状态分析法实现按键程序，用c语言编写，在51内核的单片机中成功实现，对于嵌入式开发者非常有用，该程序只用了4个按键，实现了时钟显示、调整、定时、遥控、闹钟等许多功能，适合于有一定基础的开发者用。
AD7266数据采集
- 用于控制AD7266数据采集，采用Verilog语言进行程序编写(Used for AD7266 data acquisition)
程序
- AVR单片机在ICCAVR环境下的信号采集显示和超过设定置报警程序编写(AVR microcontroller in the ICCAVR environment of signal acquisition, display and more settings, set the alarm program)
1602显示程序
- 能自己轻松编写控制要显示的字符，适合初学者练习编写程序(Easy to write their own characters to control the display, suitable for beginners to practice writing programs)
bs86d20 program
- bs86d202 的串口程序，用c语言程序编写。(Bs86d202 serial procedures, using C language programming.)
半桥LLC+同步整流DSP程序
- 该文件为由CCS6.0编写的关于半桥LLC同步整流的DSP程序。(The file is written by CCS6.0 on the half bridge LLC synchronous rectification of the DSP program)
STM32 ADC
- 基于STM32平台进行ADC采样，是对整个STM32软件配置好后，进行ADC程序编写，信号由模拟量转换为数字量，并上传到PC的过程(ADC sampling based on STM32 platform is a process of ADC programming after the STM32 software is configured, and the signal is transferred from analog to digital and uploaded to PC.)
单片机实验程序1
- 使用Proteus程序，利用P1口做输出口，接八只发光二极管。编写程序使发光二极管循环点亮。(Using the Proteus program,we use the P1 port to do the output port and connect eight light-emitting diodes. Write a program to make a LEDs cycle light.)
STM32_baseflight32.part2
- STM32，航模地面站程序编写，用于飞行器通讯和信息交流 第二部分((STM32, the aero module ground station program is written for aircraft communication and information exchange.))
污水处理PLC程序
- 西门子污水处理PLC程序，工艺流程编写程序。(Siemens sewage treatment PLC program, process flow programming.)