搜索资源列表
easystart
- 最简启动代 码 LPC2104-start substituting the most simple boot code LPC2104
S3C2410_BIOS
- 第一版YL2410开发板的BIOS 功能比较简单，上电之后，LCD显示蓝色、绿色、红色三个竖条 同时串口显示如下： Power on reset ************************************ * * * YL2410 Board BIOS V2006 * * Http://www.ucdragon.com * * * ************************************ NAND Flash Bo
fireware MicroMonitor的源代码
- An Embedded System Boot Platform The term boot monitor refers to the code that is run on a computer system as the lowest level of firmware resident to the hardware platform. You can find various types of boot monitors on a wide range of computer sys
boot
- 一个简单的引导程序,非常适合初学习者学习引导程序的编写-Guided by a simple procedure, very suitable for early learners to learn to guide the preparation of procedures
vivi-0.1.4.tar
- mizi公司的著名的BootLoader——vivi源码，基于三星s3c2410处理器的引导程序，在2410开发板上移植非常简单方便。 使用时请将后缀的.gz更改为.bz2-mizi company s well-known BootLoader- vivi source, based on Samsung S3C2410 processor boot in 2410 to develop a very simple and convenient on-board transplantati
u-boot-270-lcd.tar
- 针对yassylcd的uboot源码，lcd驱动实现简单的图形显示-Yassylcd for the uboot source, lcd drive to achieve a simple graphical display
ejtag-0.2.tar
- simple MIPS EJTAG u-boot loader
091802
- RedBoot User’s Guide:RedBoot® is an acronym for "Red Hat Embedded Debug and Bootstrap", and is the standard embedded system debug/bootstrap environment from Red Hat, replacing the existing debug/boot tools: CygMon and GDB stubs. It provides a
12f629-led-adjust
- 超简单断电复原3档亮度调光程序,每次开机都是低亮，不晃眼 低亮不是使用Pwm，而是使用电阻漏一部分电流给LED，超省电，无频闪，亮度随便调 源程序是东成的-3 super simple file recovery power brightness dimming process, each boot are low-light, non-dazzling light rather than the use of low-Pwm, but part of the use of resist
GetPath_Demo
- VC2005编写的简单程序，wince下获取当前系统启动的路径。-VC2005 write a simple program, wince obtained under the current system boot path.
ata_support
- ata 在u-boot下的支持配置选项和ata协议的中文 简单归纳-ata support by u-boot and config option ata protocal simple Chinaese
bootloader
- 简单的bootloader源代码，学开arm系列开机过程的不错的源码。-Simple bootloader source code, learning to drive arm series boot process a good source.
PowerPC_VxWorks_BSP_SBH
- BSP 用于初始化硬件、引导操作系统并提供软件和硬件之间的设备驱动接口。针对某类 体系结构的处理器开发 BSP 时，了解其基本的体系结构和指令系统是必要的。总地来说，V xWorks的启动过程凝练而精悍，流程清晰，各模块之间的耦合度很低。 VxWorks 和Linux 设备驱动的结构都相当复杂。 假设一个系统没有操作系统， 这个时候， 我们编写设备驱动的工作就完全停留在“驱使硬件行动”的层次上。然而，在 VxWorks 和 L inux 系统中整合设备驱动，则不仅仅意味着“
SimpleBoot
- 实现ARM7 S3C44B0X的简易bootLoader程序-Simple bootLoader achieve ARM7 S3C44B0X procedures
what-is-boot-loader-
- 本文介绍了什么是bootloader，bootloader的作用的，怎么实现最简单的bootloader-This article describes what is the bootloader, bootloader' s role, how to achieve the most simple bootloader
MicroOS
- 2440最简单的启动代码，自动跳入C语言，帮助理解2440启动过程-2440 boot code simple, automatic jump into the C language, 2440 boot process to help understand
yibudianji
- 异步电机的双四步启动过程，用的是c语言，比较简单，适合初学者-Induction motor dual four-step boot process, using c language, relatively simple, suitable for beginners
Bootloader-example
- 本程序简单的示范了AVR ATMEGA16的IAP应用，实现智能升级 Boot Loader XMODEM-CRC传输协议 CRC16校验-This procedure is simple demonstration of the AVR ATmega16 IAP applications, intelligent upgrade Boot Loader That XMODEM-CRC Transfer Protocol CRC16 checksum
tc35-51
- at89s52单片机控制TC35i发短信，很简单易懂的一个代码，开机就发送，附电路连接图。-at89s52 microcontroller control TC35i send text messages, a very simple and easy to understand code, boot sent the attached circuit connection diagram
dianziqin
- 用keil uvision4编写的基于51单片机的电子琴程序，可以实现21个按键对应低中高音，3个按键对应三首歌曲的自动播放，还有7个LCD可以显示一些简单的信息，比如开机欢迎界面，播放声音频率实时显示等-Written with keil uvision4 flower procedures based on 51 single-chip, low-alt, 21 keys corresponding to three buttons corresponding to the three so