搜索资源列表
Input-capture-experiments
- 输入捕获实验：在keil编译环境下的stm32输入捕获实验。-Input capture Experimental: the stm32 input keil compiler environment capture experiments.
ECT_input-capture
- 辒入捕捉（IC）：当某个被测信号的设定边沿到来时，辒入捕捉逻辑立即将自由定时器 （TCNT）的内容捕捉到16位的IC/OC寄存器中，并设置中断请求标志，随后软件可以响应中 断或者根据标志做出处理。 -Wen Capture (IC): When the arrival of a set of measured signal edge, Wen input capture logic immediately free timer (TCNT) content capture 16-bi
CAPTURE
- PIC单片机的CCP功能 //220V的交流电源直接用电阻限流,经光耦隔离,形成脉冲送到CCP2, //CCP2模块的捕捉功能,设置为每16个上升沿捕捉一次,相当于平均滤波,目的是为了减小误差 //TMR1计数的分频系数计算:假设电源为50Hz,即一个周期为20ms,16个周期为320ms //320ms=320000us,单片机用4MHz晶振,指令周期为1us,设TMR1的分频系数为K:65536×K=320000 //得K=4.88,取K=8,即TMR1的预分频系数设为1
TA-capture
- MSP420G2553捕获模式,可以捕获一个方波，并输出和捕获波形一样频率的方波。-MSP420G2553 capture mode, you can capture a square wave, and the same output and capture waveform frequency square wave.
Mini-STM32-Capture
- 正点原子开发板Mini STM32 Capture 用定时器测量三通道下降沿时间差-Punctuality atomic development board Mini STM32 Capture timer measurement with three-channel time difference falling
TIM-capture
- MC9SXS128 TIMER模块，输入捕捉-MC9SXS128 TIMER module, the input capture
stm32-capture-
- 基于stm32的捕获实验 检测时间-中断-Stm32-based capture assay time- interrupted
timer-A-capture-function
- MSP430 1611单片机通过定时器A的捕获功能，测量计算一段高电平持续时间。用来计算方波周期。-MSP430 1611 microcontroller through the timer A capture function, measurement and calculation for some high duration. Used to calculate the square wave cycle.
Event-capture
- 利用事件管理器EVA中捕获单元的捕获输入引脚检测两个事件变化的时间。（通过手动时间开关存数值）-Using the Event Manager EVA unit captured two events capture input pin to detect changes in time. (By manually switching time value stored)
MSP430-Input-capture
- 利用MSP430单片机的定时器的比较捕获模块做的小程序，用于测量输入信号的频率和周期。-Comparison of capture module to do a small program using MSP430 microcontroller timer, used for frequency and period measurement of the input signal.
freescale-Ep100ECT-capture-interrupt
- freescale ect 捕获中断程序，程序已经经过调试，成功。-freescale ect capture interrupt program, the program had already been debugging and successfully.
input-capture
- 飞思卡尔9S12系列单片机的输入捕捉程序，可以用在智能车上-Freescale 9S12 Series MCU input capture program, can be used in the smart car
PWM-Input-Capture
- 在通过输入方波信号，可以通过STM32的输入捕捉功能，测出输入方波的频率。-Through the input square wave signal, you can STM32 input capture function, measured by the frequency of the input square wave
input-capture.X
- input capture function is used to caputre the input signal in pic32. signal is captured by setting the registers
xs128-capture
- MC9S12XS128输入捕捉详细的源程序-MC9S12XS128 capture
Capture-four-PWM
- 在同一块开发板上同时输出四路PWM波，并捕获，然后把参数显示到LCD上-Four road on the same piece of development board at the same time the output PWM wave, and capture, then the parameter display on the LCD
capture
- 本次实验，使用TIM4产生一个1K的频率输出，用TIM1进行捕获。并测出频率计算 TIM1 的时基单元配置：关于TIM1的时基设置问题前文已经讨论过了。这里只有一点需要明确的，就是为了尽量减少更新事件，将TIM_Period设置到最大即0xFFFF。定时器时钟设置成2M，这样定时器的更新频率就是30Hz，不会造成两次捕获之间产生多次更新。-his experiment, using the TIM4 produce a 1 k frequency output, using TIM1 cap
capture
- 本程序是STM32系列单片机的输入捕获功能的实现，可以完成对边沿的检测，并且能通过串口将捕获的数据发送到电脑上位机上-This program is a STM32 MCU input capture function, you can complete the detection of the edge, and through the serial port to send the captured data to a computer PC
PWM-Input-Capture
- stm32单脉冲输入捕获，获取PWM的频率与占空比，可用于采集电机速度。-STM32 single pulse input capture, obtain the PWM frequency and duty ratio, can be used for the acquisition of motor speed
TIM1-input-capture
- 使用STM8的TIM1输入补获功能测PWM的占空比和周期，把被测信号接到TIM1的CH1和CH2上，当有PWM时会进入中断捕获当前计数器的值- 显示以下内容的翻译： 使用STM8的TIM1输入捕获功能测PWM的占空比和周期,把被测信号接到TIM1的CH1和CH2上,当有PWM时会进入中断捕获当前计数器的值 仍然翻译： 使用STM8的TIM1输入补获功能测PWM的占空比和周期，把被测信号接到TIM1的CH1和CH2上，当有PWM时会进入中断捕获当前计数器的值 Value using t