搜索资源列表
led(10-1)
- DSPF2812学习程序： 描述:利用GP定时器1在GPIOF8引脚上产生方波，令一个贴片LED闪烁 系统时钟150M，高速外设时钟25M，128分频后定时器周期为5.12us,适于初学者学习-DSPF2812 learning process: Descr iption: Using the GP Timer 1 GPIOF8 pin to generate a square wave, so that a flashing LED chip system clock 150M, high
led
- 简易LED 点阵汉字显示控制模块设计，包括LED汉字显示原理、电路原理图和程序设计，简单明了。-Simple LED dot-matrix character display control module design, including LED display Chinese characters principle, circuit schematic diagram and program design, simple and straightforward.
LED(c8051f)
- 用C8051F实现LED显示的C程序。源码-LED display with C8051F achieve C program. Source
led
- linux 2.6核s3c2410 led 驱动程序 -linux 2.6 Nuclear s3c2410 led driver
LED
- 点阵LED显示0-9程序（c语言）,此程序为8*8LED点阵的简单程序-Dot-matrix LED display 0-9 program (c language)
PWM-LED
- 8051单片机通过pwm调节led亮度，当PWM值增加到最大值或减小到最小值时，蜂鸣器将报警。-led light
led-pwm
- PWM 控制 LED 灯渐亮渐灭程序 适用 ME300B 开发系统 晶振为11.0592M 利用定时器控制产生占空比可变的 PWM 波 按K1，PWM值增加，则占空比减小,LED 灯渐暗。 按K2，PWM值减小，则占空比增加,LED 灯渐亮。 当PWM值增加到最大值或减小到最小值时，蜂鸣器将报警。-PWM control of LED lights getting brighter gradually eliminate procedures apply M
LED
- DSP2407 发光二极管的程序，中断控制与实现-dsp2407 program for emission of led diode
LED
- 本设计运用了基于 Nios II 嵌入式处理器的 SOPC 技术。系统以 ALTERA 公司的 Cyclone II 系列 FPGA 为数字平台，将微处理器、Avalon 总线、LED 点阵扫描控制器、存储器和人机接口控制器等硬件设备集中在一片 FPGA 上，利用片内硬件来实现 LED 点阵的带地址扫描，降低系统总功耗和简化 CPU 编程的同时，提高了系统的精确度、稳定性和抗干扰性能。-This design used the Nios II embedded processor based o
LED-Moving-Display
- 用单片机控制LED移动显示，实现拉幕数码显示-LED Mobile Display with SCM control to achieve pull-screen digital display
LED
- 单片机led上位机控制软件,com通信，VB编写-SCM led host computer control software, com communications, VB preparation
led
- cosii ARM7 S3C44B0 LED 流水灯 完整源代码-cosii ARM7 S3C44B0 LED profect
LED
- 动态LED点阵显示屏，此LED点阵显示屏是基于51单片，用595驱动，138级联扫描的，由于此类的资料网上很多，但是都没有一个拥有很详尽的说明，所以本人结合自己的实践以及整个测试的过程，给出整个代码详细的解释并分享自己总结出的经验（这些都包含在注释里了），希望对大家有用。 说明：附件里包含了代码和原理图（PROTEL DXP），只需回复就能下载了，希望大家支持。-Dynamic LED dot matrix display, the LED dot matrix display is
led
- DSP编程LED显示小程序,基于C语言编程,实现数码管显示-DSP programming LED display applet, based on C language programming, digital tube display
PWM-LED
- 软件产生PWM-LED灯D1渐亮,已通过测试.-Software generated PWM-LED lights gradually brighter D1, has been tested.
LED
- DSP开发板通过SPI接口控制LED数码管 DSP开发板通过SPI接口控制LED数码管-DSP development board through the SPI interface to control LED digital tube DSP development board through the SPI interface to control LED digital tube
LED
- LED爆闪灯，和警用的爆闪灯一样的效果。左闪三下，右闪三下。-LED lighting, and the police blasting explosive flash the same effect. Left and right under flash 3.
LED
- DSP TMS320LF2407 LED走马灯实验-DSP TMS320LF2407 LED marquee Experiment
LED
- 8X8 LED点阵显示技术在8X8 LED点阵上显示柱形，让其先从左到右平滑移动三次，其次从右到左平滑移动三次，再次从上到下平滑移动三次，最后从下到上平滑移动三次，如此循环下去。 -8X8 LED dot matrix display technology in the 8X8 LED dot matrix display column, allowed to move smoothly from left to right the first three times, followed by
led
- S3C2440 ARM开发板自己共动手写BOOTLODER系列一：LED测试程序。-S3C2440 ARM development board to write their own hands a total of BOOTLODER Series 1: LED test program.