搜索资源列表
linixtoAT91RM9200
- 这是毕业设计论文,前部分是关于嵌入式系统的综述,后部分是嵌入式系统的软件设计,完成对AT91RM9200Bootloader的移植,Linux内核的建立,串口、液晶、网络驱动程序的编写,以及文件系统的建立,为用户提供了完整的开发平台。-Graduation Thesis, the former part of the embedded system on the after part of the embedded system software design, AT91RM9200Bootlo
44b0sources
- 为44bo的嵌入式linux而编的c文件,学arm的人看看,里面有lcd及其他测试程序-44bo for embedded Linux and compile c files, learning to see the arm, There are LCD and other test procedures
1621a
- PDC605驱动程序,用于液晶屏驱动,采用SPI接口,适合单片机,LINUX驱动程序用-PDC605 driver for the LCD driver using SPI interface for microcontroller, Drivers using LINUX
755
- 基于Linux的嵌入式LCD设计,搞这方面下去-Linux-based embedded LCD design, engage in this area continue to s
au1200fb
- 为AU1200芯片linux系统所设计的LCD液晶显示驱动程序-AU1200 chip for linux system designed LCD Driver
Arm_linux_LCD
- 三星ARM的Linux系统下的LCD程序-Samsung ARM Linux system under the procedures LCD
CM240128-7
- 240*128 带中文字库的LCD模块的驱动 平台:ARM linux -240 * 128 with a Chinese font LCD module driven platforms : ARM Linux
S3C2410_BIOS
- 第一版YL2410开发板的BIOS 功能比较简单,上电之后,LCD显示蓝色、绿色、红色三个竖条 同时串口显示如下: Power on reset ************************************ * * * YL2410 Board BIOS V2006 * * Http://www.ucdragon.com * * * ************************************ NAND Flash Bo
pxa270_lcd
- pxa270驱动程序,包括处理器各个部件初始化,内存初始化,还有一个lcd控制器应用的例子。(开发环境ads或linux)-pxa270-driven procedures, including various components processor initialization, memory initialization, there is a lcd controller application examples. (Development environment ads or linu
01_lcd
- ARM9200+嵌入式linux下的lcd驱动
s3c2410lcddriver
- s3c2410的linux操作系统中LCD驱动程序
Clcddriver
- 自己改写的LCD驱动程序,基于LINUX平台。可以使用,调用函数查看里面的说明文档。
july07_3
- 基于嵌入式Linux 的 TFT LCD IP 及驱动的设计,从网上找的论文。
ARM_and_PDA
- ARM与PDA比较详细的资料包括: 基于SmartArm2200的PDA演示系统 基于ARM的PDA软硬件平台设计 基于ARM的PDA设计与实现 嵌入式Linux下彩色LCD驱动的设计与实现 嵌入式系统在军用PDA中的设计与实现.doc 一种基于ARM微处理器的电视机顶盒的设计
2410LCD
- 本程序能够在没有操作系统下可以测试LCD的驱动,在LINUX下和WINCE下都可以根据这段程序里面的寄存器设置进行驱动程序的编写!
TestLCD_Truly
- 此程序用于测试TRULY的液晶显示模块,方便同行能在Linux的嵌入式开发中开发LCD-this procedure for testing the TRULY LCD module to facilitate peer in the embedded Linux development LCD
ARM的bootloader代码
- :本文首先描述了开放源码的嵌入式硬件仿真环境SkyEye的总体架构,然后对SkyEye模拟器的LCD及TouchScreen模拟模块的设计、实现与验证过程进行了深入的阐述,并且分析比较了LCD模拟的不同实现方式。开源嵌入式GUI系统-MiniGUI和Linux操作系统在SkyEye模拟器上的成功运行说明了SkyEye模拟器的LCD及TouchScreen模拟模块的设计实现是正确和可靠的。-: This paper first describes the open source embedded
picture-to-framebuffer
- 这是一个C写的程序,它用来处理.bmp文件,经处理后的.bmp文件可以直接在Linux framebuffer上显示,作者在蓝海微芯的ARM9/2410开发板上已经使用,详细步骤在附录的.txt文件中有记录。-A small C application to change the bmp picture for displaying on the 2410 board s LCD.
lcd_test-master
- 用在arm linux上的LCD显示屏测试程序,基于底层framebuffer,显示color bar(The LCD display test program on the arm linux, based on the underlying framebuffer, displays the color bar)
L3.0.35_4.1.0_uboot_logo_keep_patch_2013-11-22
- iMX6平台u-boot启动后会运行液晶初始化程序并显示启动LOGO,但进入linux系统之后,又重新初始化一次,而且uboot与linux定义的显存地址也不一致,导致会有短暂的白屏闪烁。此补丁解决从uboot到linux启动完成一直保持LOGO不变,且中间不闪烁不闪屏。(U-boot runs the LCD initializer and displays the LOGO boot, but after entering the Linux system, it is reinitiali